- Page 1 and 2: Ross Video LimitedCDK-111A-LiteOwne
- Page 4 and 5: Important Regulatory and Safety Not
- Page 6 and 7: Company AddressRoss Video Limited R
- Page 9 and 10: ContentsIntroduction 1-1A Word of T
- Page 11 and 12: Technical Specifications...........
- Page 13 and 14: IntroductionA Word of ThanksCongrat
- Page 15: Documentation ConventionsThe follow
- Page 19 and 20: Product Comparison ChartFor your re
- Page 21 and 22: A Word about Technical SupportAt Ro
- Page 23 and 24: Installation and SetupIn This Chapt
- Page 25 and 26: OverviewCDK 11111023456798CDK111A-L
- Page 27 and 28: BNC ConnectorsThis section defines
- Page 29 and 30: Single CDK-111A-Lite Settings for R
- Page 31 and 32: Accessing the Menu SystemSetup and
- Page 33 and 34: Control Panel - DCP-111 (Optional)U
- Page 35 and 36: Navigating Through the Menus Using
- Page 37 and 38: The next series allow you to config
- Page 39 and 40: 8012345 67Card Address Configuratio
- Page 41 and 42: OperationIn This ChapterThis chapte
- Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
- Page 45 and 46: Control Panel - DCP-111 (Optional)T
- Page 47 and 48: GPIs and TalliesThis section descri
- Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
- Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
- Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
- Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
- Page 57 and 58: Menu D: Card SetupTest PatternSelec
- Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
- Page 61 and 62: Appendix A. Serial ProtocolsIn This
- Page 63 and 64: By means of “read” and “write
- Page 65 and 66: The components of the serial data a
- Page 67 and 68:
Receive commandfrom editorMake chan
- Page 69 and 70:
Message BytesThe number of message
- Page 71 and 72:
Protocol Command DescriptionsList o
- Page 73 and 74:
Bit776655Analog Control Command (45
- Page 75 and 76:
NotePush-button / Lamp Control Comm
- Page 77 and 78:
Transition Mode Command (4A, CA)Fun
- Page 79 and 80:
Rate2=Next most significant digitRa
- Page 81 and 82:
Software Version Command (6C, EC)Th
- Page 83 and 84:
Error Status Command (71, 72)The ed
- Page 85 and 86:
GVG MASTER2100 Emulation ProtocolTh
- Page 87 and 88:
Command ListThe following table lis
- Page 89 and 90:
Select Transition Type (0x03, TX_TY
- Page 91 and 92:
FunctionCrosspoint byte values:00 N
- Page 93 and 94:
Key Enable (0x0B, KEY_ENABLE)Functi
- Page 95 and 96:
FunctionQUERYErrorCodeFunctionQUERY
- Page 97 and 98:
either end of the communications li
- Page 99 and 100:
Appendix B. Software UpgradesIn Thi
- Page 101 and 102:
CautionCard may be hot to the touch
- Page 103 and 104:
Appendix C. SpecificationsIn This A
- Page 105 and 106:
Feature Comparison ChartFeature CDK
- Page 107 and 108:
CDK-111A-Lite BNC SettingsConnector
- Page 109 and 110:
I/O, Power, Delay SpecificationsTec
- Page 111 and 112:
BNC 4 (Tx) RS422/RS485 Jumper Confi
- Page 113 and 114:
Index112-Bit Analog Value..........
- Page 115 and 116:
GPIabbreviation ...................
- Page 117 and 118:
SW5, Board ID Switch ..............