CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

Getting StartedUnpackingUnpacking your CDK-111A-Lite shipment will be unique for each customer and willdepend upon your specific order. However, the following general rules will apply:• If your order includes either RossGear DFR-8110A-C orDFR-8014A-C frames, your CDK-111A-Lites will be shipped to youalready installed in the frames.NotePlease ensure that each card is properly seated before turningon the power.• If your order does not include any rack frames, the cards will beshipped to you in a 10-pack RossGear Terminal Equipment Pack box.Once the rack frames and/or boxes are unpacked, check the contents against thepacking list to ensure that all items are included. If any items are missing ordamaged, contact your sales representative or Ross Video Limited immediately.2-2 • Installation and Setup CDK-111A-Lite • Owner’s Guide v4B
OverviewCDK 11111023456798CDK111A-Lite Card, Component Side1) USB Port (Not Implemented) 5) Menu Select / FTB Button 9) GPI, Panel, Tally Jumper Block2) Menu Selector 6) Board ID Switch 10) RX Termination Jumper Block3) Menu Up Button 7) Reset Button and Download Connector4) Menu Down / Key Button 8) EDH Insertion Jumper Block1) USB Port (J2)Not implemented.2) Menu Selector (SW1)The Menu Selector is a 16 position rotary knob, labeled 0 to F. It isused to select the various menus for card installation and operation.3) Menu Up Button (SW2)Menu mode – this button moves the cursor to the item above on themenu. A momentary press will advance one item. When an item isselected, holding the button will scroll up through the possible values.4) Menu Down / Key Button (SW3)Operation mode – this button will dissolve a key on or off. It uses thetransition rate set in the menu.Menu mode – this button moves the cursor to the item below on themenu. A momentary press will advance one item. When an item isselected, holding the button will scroll up through the possible values.5) Menu Select / FTB Button (SW4)Operation mode – this button fades the PGM output to black or bringsthe PGM up from black, depending upon its present state. It uses thetransition rate set in the menu.Menu mode – this button moves the cursor to the sub-menu values inthe right-hand column. The values in these sub-items can then beadjusted using the Menu Up or Menu Down button. Pressing theMenu Select button again will return the cursor to the left-handcolumn.CDK-111A-Lite • Owner’s Guide v4B Installation and Setup • 2-3
Page 1 and 2: Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5: Important Regulatory and Safety Not
Page 6 and 7: Company AddressRoss Video Limited R
Page 9 and 10: ContentsIntroduction 1-1A Word of T
Page 11 and 12: Technical Specifications...........
Page 13 and 14: IntroductionA Word of ThanksCongrat
Page 15 and 16: Documentation ConventionsThe follow
Page 17 and 18: AbbreviationsThe following abbrevia
Page 19 and 20: Product Comparison ChartFor your re
Page 21 and 22: A Word about Technical SupportAt Ro
Page 23: Installation and SetupIn This Chapt
Page 27 and 28: BNC ConnectorsThis section defines
Page 29 and 30: Single CDK-111A-Lite Settings for R
Page 31 and 32: Accessing the Menu SystemSetup and
Page 33 and 34: Control Panel - DCP-111 (Optional)U
Page 35 and 36: Navigating Through the Menus Using
Page 37 and 38: The next series allow you to config
Page 39 and 40: 8012345 67Card Address Configuratio
Page 41 and 42: OperationIn This ChapterThis chapte
Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
Page 45 and 46: Control Panel - DCP-111 (Optional)T
Page 47 and 48: GPIs and TalliesThis section descri
Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
Page 57 and 58: Menu D: Card SetupTest PatternSelec
Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73 and 74: Bit776655Analog Control Command (45
Page 75 and 76:
NotePush-button / Lamp Control Comm
Page 77 and 78:
Transition Mode Command (4A, CA)Fun
Page 79 and 80:
Rate2=Next most significant digitRa
Page 81 and 82:
Software Version Command (6C, EC)Th
Page 83 and 84:
Error Status Command (71, 72)The ed
Page 85 and 86:
GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88:
Command ListThe following table lis
Page 89 and 90:
Select Transition Type (0x03, TX_TY
Page 91 and 92:
FunctionCrosspoint byte values:00 N
Page 93 and 94:
Key Enable (0x0B, KEY_ENABLE)Functi
Page 95 and 96:
FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98:
either end of the communications li
Page 99 and 100:
Appendix B. Software UpgradesIn Thi
Page 101 and 102:
CautionCard may be hot to the touch
Page 103 and 104:
Appendix C. SpecificationsIn This A
Page 105 and 106:
Feature Comparison ChartFeature CDK
Page 107 and 108:
CDK-111A-Lite BNC SettingsConnector
Page 109 and 110:
I/O, Power, Delay SpecificationsTec
Page 111 and 112:
BNC 4 (Tx) RS422/RS485 Jumper Confi
Page 113 and 114:
Index112-Bit Analog Value..........
Page 115 and 116:
GPIabbreviation ...................
Page 117 and 118:
SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

Create successful ePaper yourself

Delete template?

Save as template?