CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

Key Modifier (0x0A, KEY_MOD)This command selects the characteristics for the requested key. The squeeze backfield has no effect. The “Keyer Select” parameter selects keyer 1 only formodification.FunctionKey Modifier (0x0A, KEY_MOD)Keyer SelectCommand Data FieldsKeyModifierSqueezeBackCOMMAND 1 byte 1 byte 1 byteQUERY1 byteREPLY 1 byte 1 byte 1 byteKeyer Select byte value 101 Keyer 1 selectKey Modifier bit settingsBit 0 0 = Self1 = ExternalBit 1 0 = Matte1 = VideoBit 2-4 IgnoredBit 5-7 ReservedSqueezeBack Position byte values 200 No change1. One keyer must be selected for the command format of this field. One keyer may be selected for thequery format of this field. No keyers selected is an invalid condition.2. Not yet implemented.Key Enable (0x0B, KEY_ENABLE)This command selects Keyer 1 to be on or off air after the next transition.• Selecting a Keyer (bit=1) at the next transition will take an off-air key onair,or leave an on-air key on-air. Setting (bit=0) has a similar, butcomplimentary effect.• Selecting a Keyer (bit=1) for a currently off-air Keyer will cause that Key tobe seen on the PST bus.See comments in the TX_NEXT command notes concerning interaction with theKEY_ENABLE command.4-32 • Appendix A. Serial Protocols CDK-111A-Lite • Owner’s Guide v4B
Key Enable (0x0B, KEY_ENABLE)FunctionCOMMANDQUERYREPLYCommand Data FieldKeyer Select1byte1 byteKeyer Select byte values 101 Keyer 1Bit 2-7 Ignored/Reserved1. One or more keyers must be selected for the command format of this field. Only one keyer may beselected for the query format of this field. No keyers selected is an invalid condition.Key Status (0x0C, KEY_STAT)This command indicates that status for Keyer 1 if not physically present will bereported as off-air. Use the System Status and System Configuration commands toobtain more information.Key Status (0x0C, KEY_STAT)FunctionQUERYREPLYCommand Data FieldKeyer Status1 byteKeyer Status bit settingsBit 0 Keyer 1 (0 = Off air, 1 = On air)Bit 1-7 Ignored/ ReservedAutomation Enable Status (0x0D, AUTO_STAT)This command send an Enabled reply to a Status query. On the CDK-111A-Lite, theAutomation interface cannot be disabled.Automation Enable Status (0x0D, AUTO_STAT)FunctionQUERYREPLYCommand Data FieldKeyer Status1 byteStatus byte value01 EnabledCDK-111A-Lite • Owner’s Guide v4B Appendix A. Serial Protocols • 4-33
Page 1 and 2:
Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5:
Important Regulatory and Safety Not
Page 6 and 7:
Company AddressRoss Video Limited R
Page 9 and 10:
ContentsIntroduction 1-1A Word of T
Page 11 and 12:
Technical Specifications...........
Page 13 and 14:
IntroductionA Word of ThanksCongrat
Page 15 and 16:
Documentation ConventionsThe follow
Page 17 and 18:
AbbreviationsThe following abbrevia
Page 19 and 20:
Product Comparison ChartFor your re
Page 21 and 22:
A Word about Technical SupportAt Ro
Page 23 and 24:
Installation and SetupIn This Chapt
Page 25 and 26:
OverviewCDK 11111023456798CDK111A-L
Page 27 and 28:
BNC ConnectorsThis section defines
Page 29 and 30:
Single CDK-111A-Lite Settings for R
Page 31 and 32:
Accessing the Menu SystemSetup and
Page 33 and 34:
Control Panel - DCP-111 (Optional)U
Page 35 and 36:
Navigating Through the Menus Using
Page 37 and 38:
The next series allow you to config
Page 39 and 40:
8012345 67Card Address Configuratio
Page 41 and 42: OperationIn This ChapterThis chapte
Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
Page 45 and 46: Control Panel - DCP-111 (Optional)T
Page 47 and 48: GPIs and TalliesThis section descri
Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
Page 57 and 58: Menu D: Card SetupTest PatternSelec
Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73 and 74: Bit776655Analog Control Command (45
Page 75 and 76: NotePush-button / Lamp Control Comm
Page 77 and 78: Transition Mode Command (4A, CA)Fun
Page 79 and 80: Rate2=Next most significant digitRa
Page 81 and 82: Software Version Command (6C, EC)Th
Page 83 and 84: Error Status Command (71, 72)The ed
Page 85 and 86: GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88: Command ListThe following table lis
Page 89 and 90: Select Transition Type (0x03, TX_TY
Page 91: FunctionCrosspoint byte values:00 N
Page 95 and 96: FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98: either end of the communications li
Page 99 and 100: Appendix B. Software UpgradesIn Thi
Page 101 and 102: CautionCard may be hot to the touch
Page 103 and 104: Appendix C. SpecificationsIn This A
Page 105 and 106: Feature Comparison ChartFeature CDK
Page 107 and 108: CDK-111A-Lite BNC SettingsConnector
Page 109 and 110: I/O, Power, Delay SpecificationsTec
Page 111 and 112: BNC 4 (Tx) RS422/RS485 Jumper Confi
Page 113 and 114: Index112-Bit Analog Value..........
Page 115 and 116: GPIabbreviation ...................
Page 117 and 118: SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?