CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

Menu E: Tally / GPI SetupMenu E: Tally / GPI SetupGPI #1 (BNC 2) GPI Function for GPI #1. This is only used if BNC 2 is set to GPI #1 in Menu D: CardSetup and jumper J6 is bridged at pins 1 and 2.• USED FOR COMM (default setting)• USED FOR TALLY• AUTO FTB• AUTO KEY 1• CUT KEY 1GPI #1 Trigger GPI Trigger for GPI #1.• EDGE HIGH (default setting)• EDGE LOW• LEVEL HIGH• LEVEL LOWGPI #2 (BNC 3) GPI Function for GPI #2. This is only used if BNC 3 is set to GPI #2 in Menu D: CardSetup. See GPI #1 list for options available here. (same default settings as BNC 2)GPI #2 Trigger GPI Trigger for GPI #2. See GPI #1 Trigger options. (same default settings as BNC 2)GPI #3 (BNC 3) GPI Function for GPI #3. This is only used if BNC 4 is set to GPI #3 in Menu D: CardSetup. See GPI #1 list for options available here. (same default settings as BNC 2)GPI #3 Trigger GPI Trigger for GPI #3. See GPI #1 Trigger options. (same default settings as BNC 2)Tally #1 (BNC 2) Tally Function for Tally #1: This is only used if BNC 2 is set to TALLY #1 in Menu D:Card Setup and jumper J6 is bridged at pins 5 and 6.• USED FOR COMM (default setting)• USED FOR GPI• KEY 1Tally #1 Trigger Tally Trigger for Tally #1.• LEVEL HIGH (default setting)• LEVEL LOWTally #2 (BNC 3) Tally Function for Tally #2: This is only used if BNC 3 is set to TALLY #2 in Menu D:Card Setup. See Tally #1 list for options available here. (same default settings as BNC 2)Tally #2 Trigger Tally Trigger for Tally #2.• LEVEL HIGH (default setting)• LEVEL LOWTally #3 (BNC 4) Tally Function for Tally #3: This is only used if BNC 4 is set to TALLY #3 in Menu D:Card Setup. See Tally #1 list for options available here. (same default settings as BNC 2)Tally #3 Trigger Tally Trigger for Tally #3.• LEVEL HIGH (default setting)• LEVEL LOW3-18 • Operation CDK-111A-Lite • Owner’s Guide v4B
Menu F: BNC ListingMenu F: BNC ListingThis menu is for informational purposes only. The BNC listing is designed for easy reference during cardconfiguration and troubleshooting. This menu reflects configurations set in Menu D.BNC INBNC 1BNC 2BNC 3BNC 4BNC 5BNC 6BNC 7BNC 8Key 1 StatusFTB StatusTime ActiveBKGD 1 INPUT (default setting)UnusedDepends upon card configuration (GPI, CONTROL PANEL (default setting), or TALLY)Depends upon card configuration (GPI, TALLY, or RX (default setting))Depends upon card configuration (GPI, TALLY, or TX (default setting))PROGRAM (default setting)PROGRAM (default setting)KEY VIDEO INPUT (default setting)KEY ALPHA INPUT (default setting)Whether Key 1 is currently ON AIR or OFF AIR (default setting).ON/OFF (default setting). Whether the card is currently faded to black or not.The time begins counting up when the card is powered on. If the card continues to be inservice with uninterrupted power for a period of approx. 2 ¼ years, it will reset to 0 andbegin counting up again.CDK-111A-Lite • Owner’s Guide v4B Operation • 3-19
Page 1 and 2:
Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5:
Important Regulatory and Safety Not
Page 6 and 7:
Company AddressRoss Video Limited R
Page 9 and 10: ContentsIntroduction 1-1A Word of T
Page 11 and 12: Technical Specifications...........
Page 13 and 14: IntroductionA Word of ThanksCongrat
Page 15 and 16: Documentation ConventionsThe follow
Page 17 and 18: AbbreviationsThe following abbrevia
Page 19 and 20: Product Comparison ChartFor your re
Page 21 and 22: A Word about Technical SupportAt Ro
Page 23 and 24: Installation and SetupIn This Chapt
Page 25 and 26: OverviewCDK 11111023456798CDK111A-L
Page 27 and 28: BNC ConnectorsThis section defines
Page 29 and 30: Single CDK-111A-Lite Settings for R
Page 31 and 32: Accessing the Menu SystemSetup and
Page 33 and 34: Control Panel - DCP-111 (Optional)U
Page 35 and 36: Navigating Through the Menus Using
Page 37 and 38: The next series allow you to config
Page 39 and 40: 8012345 67Card Address Configuratio
Page 41 and 42: OperationIn This ChapterThis chapte
Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
Page 45 and 46: Control Panel - DCP-111 (Optional)T
Page 47 and 48: GPIs and TalliesThis section descri
Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
Page 57: Menu D: Card SetupTest PatternSelec
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73 and 74: Bit776655Analog Control Command (45
Page 75 and 76: NotePush-button / Lamp Control Comm
Page 77 and 78: Transition Mode Command (4A, CA)Fun
Page 79 and 80: Rate2=Next most significant digitRa
Page 81 and 82: Software Version Command (6C, EC)Th
Page 83 and 84: Error Status Command (71, 72)The ed
Page 85 and 86: GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88: Command ListThe following table lis
Page 89 and 90: Select Transition Type (0x03, TX_TY
Page 91 and 92: FunctionCrosspoint byte values:00 N
Page 93 and 94: Key Enable (0x0B, KEY_ENABLE)Functi
Page 95 and 96: FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98: either end of the communications li
Page 99 and 100: Appendix B. Software UpgradesIn Thi
Page 101 and 102: CautionCard may be hot to the touch
Page 103 and 104: Appendix C. SpecificationsIn This A
Page 105 and 106: Feature Comparison ChartFeature CDK
Page 107 and 108: CDK-111A-Lite BNC SettingsConnector
Page 109 and 110:
I/O, Power, Delay SpecificationsTec
Page 111 and 112:
BNC 4 (Tx) RS422/RS485 Jumper Confi
Page 113 and 114:
Index112-Bit Analog Value..........
Page 115 and 116:
GPIabbreviation ...................
Page 117 and 118:
SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?