CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

FunctionREAD:ByteCountEffectsAddressAnalog Control Command (45, C5)CommandCodeMessageAnalog Controls 03 01 45 Analog #WRITE:MLE 1 AnalogControlsMLE 1 all 4 MaskEdge Controls **05 01 C5 Analog # and valueAnalog #, LSB, MSB0B 01 C5 7F, top (LSB, MSB), Bottom (LSB, MSB),Left (LSB, MSB), Right (LSB, MSB)Control #Control NameAnalog Control Numbers00 Fader Knob0ACLIP0BGAIN0C**MASK TOP0D** MASK LEFT0E**MASK RIGHT0F**MASK BOTTOM18, (14) MATTE FILL –HUE19, (1F) MATTE FILL – SAT1A, (1B) MATTE FILL - LUM50** TRANSPARENCY (0000 – 0FFF, 0000 = opaque, 0FFF = transparent)7F**MASK – TOP – BOTTOM – LEFT – RIGHTUsed to decrease message traffic.**Ross Video custom extension to GVG 100 protocol. Write Byte Count varies according to control number. Read Byte Count is 3.4-14 • Appendix A. Serial Protocols CDK-111A-Lite • Owner’s Guide v4B
NotePush-button / Lamp Control Command (46/47, C6/C7)The read command is used by the editor to determine the status of a push-button andits associated lamp or LED. The keyer will, in turn, respond with the appropriateform of the write command, indicating either the “on” or “off” state of the specifiedpush-button / lamp (PB/L).The write command is used to turn the designated PB/L “on” or “off”. Use of aninvalid PB/L number within a write command will cause the keyer to ignore thecommand.Commands 46 and 47 are identical. If an invalid PB/L numberis specified in the read command, the reply will indicate anOFF status for a fictitious PB/L 00(H)Push-button / Lamp Control Command (46/47, C6/C7)Function Byte Count EffectsAddressREAD:CommandCodeMessageKeyer PB/L 03 01 46/47 PB/L numberWRITE:Keyer PB/L On 03 01 C6 PB/L numberKeyer PB/L Off 03 01 C7 PB/L numberThe Push-button / Lamp control command has limitations due the functionaldifferences inherent in two types of push buttons on control panels; mutuallyexclusive and alternate-action. Mutually exclusive push-buttons are interlocked sothat only one push-button in a group can be selected at a time; selecting one cancelsany others in the group. In such groups, the C6 (write on) command will turn off thecurrently lighted button when another button is selected, but there is no action takenif the C7 (write off) command is sent to turn off the currently lighted button. Keyerlogic requires that one button must always be selected.The alternate-action type of push-button changes state each time the button ispressed, turning off on the first time it is selected, off the second time, on again thethird, and so on. In the alternate-action groups, the Push-button / Lamp controlcommand must select the correct “next state” – on or off – of the push-button orthere will be no change to the status of the push-button.CDK-111A-Lite • Owner’s Guide v4B Appendix A. Serial Protocols • 4-15
Page 1 and 2:
Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5:
Important Regulatory and Safety Not
Page 6 and 7:
Company AddressRoss Video Limited R
Page 9 and 10:
ContentsIntroduction 1-1A Word of T
Page 11 and 12:
Technical Specifications...........
Page 13 and 14:
IntroductionA Word of ThanksCongrat
Page 15 and 16:
Documentation ConventionsThe follow
Page 17 and 18:
AbbreviationsThe following abbrevia
Page 19 and 20:
Product Comparison ChartFor your re
Page 21 and 22:
A Word about Technical SupportAt Ro
Page 23 and 24: Installation and SetupIn This Chapt
Page 25 and 26: OverviewCDK 11111023456798CDK111A-L
Page 27 and 28: BNC ConnectorsThis section defines
Page 29 and 30: Single CDK-111A-Lite Settings for R
Page 31 and 32: Accessing the Menu SystemSetup and
Page 33 and 34: Control Panel - DCP-111 (Optional)U
Page 35 and 36: Navigating Through the Menus Using
Page 37 and 38: The next series allow you to config
Page 39 and 40: 8012345 67Card Address Configuratio
Page 41 and 42: OperationIn This ChapterThis chapte
Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
Page 45 and 46: Control Panel - DCP-111 (Optional)T
Page 47 and 48: GPIs and TalliesThis section descri
Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
Page 57 and 58: Menu D: Card SetupTest PatternSelec
Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73: Bit776655Analog Control Command (45
Page 77 and 78: Transition Mode Command (4A, CA)Fun
Page 79 and 80: Rate2=Next most significant digitRa
Page 81 and 82: Software Version Command (6C, EC)Th
Page 83 and 84: Error Status Command (71, 72)The ed
Page 85 and 86: GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88: Command ListThe following table lis
Page 89 and 90: Select Transition Type (0x03, TX_TY
Page 91 and 92: FunctionCrosspoint byte values:00 N
Page 93 and 94: Key Enable (0x0B, KEY_ENABLE)Functi
Page 95 and 96: FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98: either end of the communications li
Page 99 and 100: Appendix B. Software UpgradesIn Thi
Page 101 and 102: CautionCard may be hot to the touch
Page 103 and 104: Appendix C. SpecificationsIn This A
Page 105 and 106: Feature Comparison ChartFeature CDK
Page 107 and 108: CDK-111A-Lite BNC SettingsConnector
Page 109 and 110: I/O, Power, Delay SpecificationsTec
Page 111 and 112: BNC 4 (Tx) RS422/RS485 Jumper Confi
Page 113 and 114: Index112-Bit Analog Value..........
Page 115 and 116: GPIabbreviation ...................
Page 117 and 118: SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

Create successful ePaper yourself

Delete template?

Save as template?