CDK-111A-Lite Owner's Guide - Ross Video

More documents

Recommendations

Info

16 or More CardsFor facilities that have 16 or more cards, the menu system must be used to assign aunique address for each card. This address is used by the serial device tocommunicate with an individual card.To set the card address (16-127 cards):1. Set the Board ID Switch on each card to 0 before assigning anyaddresses with the menu.2. Using the Menu Selector knob on the card edge, navigate toMenu C: Secondary Card Setup.Menu C: Secondary Card SetupNoteSee Chapter 3, “Operation” for details on Menu C items andtheir parameters.3. For each card, navigate to the Board Addr item and press theMenu Select button on the card edge to move the cursor to themenu item’s submenu column.NoteThe Board Addresses are displayed in hexadecimal and rangefrom 0 (Hex) to FC (Hex). Addresses must be even numbers (asystem requirement), and, therefore, the system is limited to atotal of 127 uniquely numbered cards.This is also the total number of cards that can be controlledfrom a single serial port.For those not familiar with working in hexadecimal, the evendigits are those that end in 0, 2, 4, 6, 8, A, C, and E.4. Systematically enter the Board Addr item in each card and set itsaddress to a unique even number.5. When you have set a card’s address, press the Menu Select buttonagain to return you to the left hand column.6. Rotate the Menu Selector knob to the 0 position to save the dataand exit the menu system.This concludes the installation and setup section for your CDK-111A-Lite.2-18 • Installation and Setup CDK-111A-Lite • Owner’s Guide v4B
OperationIn This ChapterThis chapter describes in detail the function of all card edge buttons and knobs,control panel buttons, and the internal menus used during the operation of theCDK-111A-Lite.Specifically, the following topics are discussed:• Card Edge Controls• LED functions• Control Panel – DCP-111 (Optional)• GPIs and Tallies• The Menu System• The MenusCDK-111A-Lite • Owner’s Guide v4B Operation • 3-1
Page 1 and 2: Ross Video LimitedCDK-111A-LiteOwne
Page 4 and 5: Important Regulatory and Safety Not
Page 6 and 7: Company AddressRoss Video Limited R
Page 9 and 10: ContentsIntroduction 1-1A Word of T
Page 11 and 12: Technical Specifications...........
Page 13 and 14: IntroductionA Word of ThanksCongrat
Page 15 and 16: Documentation ConventionsThe follow
Page 17 and 18: AbbreviationsThe following abbrevia
Page 19 and 20: Product Comparison ChartFor your re
Page 21 and 22: A Word about Technical SupportAt Ro
Page 23 and 24: Installation and SetupIn This Chapt
Page 25 and 26: OverviewCDK 11111023456798CDK111A-L
Page 27 and 28: BNC ConnectorsThis section defines
Page 29 and 30: Single CDK-111A-Lite Settings for R
Page 31 and 32: Accessing the Menu SystemSetup and
Page 33 and 34: Control Panel - DCP-111 (Optional)U
Page 35 and 36: Navigating Through the Menus Using
Page 37 and 38: The next series allow you to config
Page 39: 8012345 67Card Address Configuratio
Page 43 and 44: 4) Menu Select/FTB Button (SW4)•
Page 45 and 46: Control Panel - DCP-111 (Optional)T
Page 47 and 48: GPIs and TalliesThis section descri
Page 49 and 50: The Menu SystemThe CDK-111A-Lite is
Page 51 and 52: Menu 1: Runtime ParametersAuto Tran
Page 53 and 54: Menu 4: Box Mask PositioningMenu 4:
Page 55 and 56: Menu A: DiagnosticsMenu A: Diagnost
Page 57 and 58: Menu D: Card SetupTest PatternSelec
Page 59 and 60: Menu F: BNC ListingMenu F: BNC List
Page 61 and 62: Appendix A. Serial ProtocolsIn This
Page 63 and 64: By means of “read” and “write
Page 65 and 66: The components of the serial data a
Page 67 and 68: Receive commandfrom editorMake chan
Page 69 and 70: Message BytesThe number of message
Page 71 and 72: Protocol Command DescriptionsList o
Page 73 and 74: Bit776655Analog Control Command (45
Page 75 and 76: NotePush-button / Lamp Control Comm
Page 77 and 78: Transition Mode Command (4A, CA)Fun
Page 79 and 80: Rate2=Next most significant digitRa
Page 81 and 82: Software Version Command (6C, EC)Th
Page 83 and 84: Error Status Command (71, 72)The ed
Page 85 and 86: GVG MASTER2100 Emulation ProtocolTh
Page 87 and 88: Command ListThe following table lis
Page 89 and 90: Select Transition Type (0x03, TX_TY
Page 91 and 92:
FunctionCrosspoint byte values:00 N
Page 93 and 94:
Key Enable (0x0B, KEY_ENABLE)Functi
Page 95 and 96:
FunctionQUERYErrorCodeFunctionQUERY
Page 97 and 98:
either end of the communications li
Page 99 and 100:
Appendix B. Software UpgradesIn Thi
Page 101 and 102:
CautionCard may be hot to the touch
Page 103 and 104:
Appendix C. SpecificationsIn This A
Page 105 and 106:
Feature Comparison ChartFeature CDK
Page 107 and 108:
CDK-111A-Lite BNC SettingsConnector
Page 109 and 110:
I/O, Power, Delay SpecificationsTec
Page 111 and 112:
BNC 4 (Tx) RS422/RS485 Jumper Confi
Page 113 and 114:
Index112-Bit Analog Value..........
Page 115 and 116:
GPIabbreviation ...................
Page 117 and 118:
SW5, Board ID Switch ..............
show all

CDK-111A-Lite Owner's Guide - Ross Video

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?