ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

More documents

Recommendations

Info

ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6131-74-101It is advisable during normal operationto leave the speed in the defaultsetting of “normal”.The value for the constant brightnesscontroller can be selected with theLux1 potentiometer of the presencedetector or via the ETS software. If thesetpoint adjustment is carried out viaETS, it is possible to enter a setpointfor the constant brightness controllerdirectly. This can be a brightness valuebetween 5 and 1000 luxn. It is howevera better idea to let the user set therequired brightness value directly. Todo so, the ETS2 program enables thecommunication object “Constantbrightness controller - Save act.brightness value”. As soon as atelegram with the value “1” is receivedat this object, the presence detectoradopts the current brightness value asthe new setpoint for the constantbrightness controller.A new setpoint for the constantbrightness controller can be assignedat any time via the 1 bytecommunication object “Constantbrightness controller - Brightnesssetpoint/act. value” (see example).If the user leaves the room, thepresence detector starts its normalrecovery time which can be set on thetab “Adjustments channel 1”. However,if the user has previously adapted thebrightness value to his requirementsvia the dimming objects, the presencedetector starts the recovery time for aninactive constant brightness controller,once the normal recovery time haselapsed. This means that if someoneenters the room during this period, thecombined presence detector andswitch/dim actuator will not directlystart the constant brightness controller.The switch/dim actuator will switch onwith the last active brightness value.The presence detector can switch onor disable the constant brightnesscontroller mode directly after busvoltage recovery. There is acorresponding option on the “General”page.The current “Brightness setpoint/act.value” is not stored after a bus voltagefailure. If a specific brightness valueshould be set after bus voltagerecovery, it should be sent again to theobject “Constant brightness controller -Brightness setpoint/act. value”.Example:A constant brightness controller shouldbe used in a sports hall for energysaving. In leisure mode, the lightingshould be regulated to a brightnesslevel of 200 lux while in competitionmode the brightness should beregulated to 500 lux.The presence detector is usedtogether with the switch/dim actuatorFM and a 1-fold switch sensor(application “Value”) to toggle the twotypes of constant brightness control.The combined presence detector andswitch/dim actuator must be installedin a suitable position and put intooperation. After the commissioningstage, the illuminance should bedetermined with a measuring device.The current brightness value of theactuator can be modified via thedimming objects until an illuminance of200 lux is achieved.The communication object “Constantbrightness controller - Brightnesssetpoint/act. value” must then be readout with the help of ETS2. To do so,select “Groups” from the “Test” menuand enter the group address in the“Read value” tab which has beenentered in the communication objectabove. You should then either writedown the value which is sent in theresponse or store it directly in theparameter window of the 1-fold switchsensor.Dim the actuator up again until a valueof 500 lux is reached. You should againsend a read request to the object“Constant brightness controller -Brightness setpoint/act. value”. Writedown the value of the responsetelegram again or enter it directly in theparameters of the 1-fold switch sensor.If you have not already done so, enterthe two recorded values in theparameter window of the 1-fold switchsensor. When selecting the applicationof the switch sensor, it should beensured that the rockers can send1 byte values.Put the switch sensor into operationand constant brightness control isimplemented with the toggling of twooperating modes.March 2003 8 - 95
ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6131-74-101Additional communication objectsfor switch/dim actuator FMNo. Type Object name Function…6 1 bit Output Switching7 4 bit Dimmer Rel. dimming8 1 byte Dimmer Brightness value9 1 bit Constant brightness controller Activation11 1 byte Constant brightness controller Brightness setpoint/act. valueCommunication objectswith object for storing the currentbrightness valueNo. Type Object name Function…10 1 bit Constant brightness controller Save act. brightness value…Parameters for “Low Access”The default setting for the valuesis printed in bold type.Parameters for “High Access”The default setting for the valuesis printed in bold type.Constant brightness controllerwith “Low Access”:– Type of dimming actuator internal and external dimmerinternal dimmer– Activation object constant brightness not availablecontrolavailableOnly if activation object is available:– enabling constant brightness ON telegramcontrol atOFF telegram– Switch ON brightness 10% brightness / … / 50% brightness /… / 100% brightness– Speed of control Test mode (8.2ms*30)fast (8.2ms*50)normal (130ms*7)slow(130ms*14)General:Behaviour on bus voltage recovery(communication objects)– Constant brightness controller disabledenabledAdditional parameters for “High Access”:– Setpoint adjustable with ETSLux1 potentiometerOnly if “ETS” is selected:– Setpoint brightness control 5(5 lux … 1000 lux)– Recovery time of inactive constant ETSbrightness controller is adjusted by Illumination potentiometerOnly if “ETS” is selected:– Time base of recovery time 0.5 ms / 8.2 ms / 130 ms / 2.1 s / 34 s /9 min– Time factor of recovery time 1008 - 96 March 2003
Page 1 and 2: ABB i-bus ® EIBSwitch/dim actuator
Page 19: ABB i-bus ® EIBSwitch/dim actuator
Page 71 and 72:
ABB i-bus ® EIBSwitch/dim actuator
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
show all

ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

Create successful ePaper yourself

Delete template?

Save as template?