ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

More documents

Recommendations

Info

ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500Application programs in ETS Number of Max. number of Max. number ofcommunication objects group addresses associationsFor 1-fold Busch-triton ® switch sensor:Switch Dim Shutter Flex. Alloc. Logic Status /4 11 11 23For 3-fold Busch-triton ® switch sensor:IR Switch Dim Shutter Lightscene /8 19 19 19For 3-fold Busch-triton ® switch sensor with display:IR LCD Switch Dim Shutter Lightscene /4 19 19 19For 5-fold Busch-triton ® switch sensor:IR Switch Dim Shutter /1 17 18 18IR Switch Dim Shutter Lightscene /4 19 19 19For 5-fold Busch-triton ® switch sensor with display:IR LCD Switch Dim Shutter /3 19 24 20IR LCD Switch Dim Shutter Lightscene /3 19 19 21March 2003 8 - 79
ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500Switch Dim Logic Status Fixedvalue /1Selection in ETS2– ABBIlluminationDimmer– ABBFM Dimmer actuator/sensorwithout operating elementThe application program is intendedfor the flush-mounted switch/dimactuator without a further applicationmodule.SwitchThe output can be switched on and offvia the 1 bit communication object“Dimmer - Switching”. The samecommunication object also sends atelegram if the output changes its statebecause e.g. the 4 bit object no. 1“Dimmer” or the 1 byte object no. 2“Dimmer” has received a telegram.If the output objects of several switch/dim actuators use the same groupaddresses, the parameter “Operationmode by paralleling ...” must be takeninto account. Only one device may beset to “Master”. The other devices mustuse the “Slave” setting. If this is notobserved, the devices may continuallysend telegrams to each other.The brightness value, which is used bythe switch/dim actuator FM when it isswitched on, is defined in theparameters. A constant value between10% brightness and 100% brightnesscan be selected. Alternatively, theactuator stores the value of the object“Brightness value” at the point when itwas switched off via the switchingobject and then recreates it.DimThe connected luminaire can bedimmed in accordance with EIS 2 withthe 4 bit communication object“Dimmer”. If the actuator is switched off,it can be dimmed on via the 4 bitobject.The interval for passing through thedimming range can be set with the twoparameters “Time base ...” and “Factor...”. The actuator uses the formulaTotal time = Base * Factor.Using the 1 byte communication objectno. 2, the luminaire can be assignedone of 256 brightness values in arange between 0 = switched off and255 = full brightness. It is defined viathe parameter “Behaviour on changein the brightness value” whether thenew value is set immediately (“jump tovalue”) or with the selected dimmingspeed (“dim to value”).StatusIf the parameter “Status response” isset to “yes”, the ETS2 programdisplays a further 1 bit object “Statusresponse”. As soon as the switch/dimactuator is switched on, regardless ofthe brightness value, a telegram issent with the value “1”. If the actuator isswitched off again, a “0” is sent.LogicIt is possible to set an AND or ORfunction with the parameter “Logicalconnection”. In both cases, ETS2displays an additional communicationobject. The actuator links the values ofobjects no. 0 “Switching” and no. 3 “...connection” and then switches theoutput. Even in this case, theparameter “Status response” enablesprecise monitoring of the actual outputstate.Read-only memoryThe actuator has three 1 bitcommunication objects “Read-onlymemory ...”. It is possible to set up to sixvalues with the two possible objectvalues “0” and “1”. The parameters“Value for read-only memory ...” areused for this purpose. The number ofread-only memory devices that areactually in use is defined with theparameters “Number of objects” and“Behaviour receiving an OFFtelegram”.Bus voltage failure / recoveryOn bus voltage failure, the switch/dimactuator FM switches off the connectedluminaires. On bus voltage recovery,the luminaires remain switched off inthe normal state. It is however alsopossible to set the minimum ormaximum brightness or the lastbrightness value that was stored priorto the voltage failure.8 - 80 March 2003
Page 1 and 2: ABB i-bus ® EIBSwitch/dim actuator
Page 3: ABB i-bus ® EIBSwitch/dim actuator
Page 55 and 56:
ABB i-bus ® EIBSwitch/dim actuator
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
show all

ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

Create successful ePaper yourself

Delete template?

Save as template?