ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

More documents

Recommendations

Info

ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6324-xxLightscenesIn lightscene mode, up to six sceneswith up to six different groups ofactuators can be controlled withoutspecial lightscene modules.The lightscenes can be specified viathe device parameters. The user canthen reconfigure the parametersindividually according to hisrequirements while the installation is inoperation. The auxiliary push button isused for storing new lightscenes(parameters). To do this, the parameter“Function of auxiliary push button”must be set to “Save lightscenes”. Tobe able to use this function, thetransmitting group addresses and flagsmust be assigned correctly whenconfiguring the actuators.The lightscenes are configuredaccording to the following process.1. The number of lightscenes and theirrespective rocker assignment can beset on the “General” parameterpage.2. For each of the actuator groupsA ... F, it must be determined with theparameter “Type of actuator group...”, whether they use 1 bitcommunication objects (switch orshutter actuators) or 8 bitcommunication objects (dimmingactuators). Depending on thissetting, the ETS2 program displaysvarious parameters andcommunication objects.Communication objects 13 ... 18 areused for the control of actuatorgroups A ... F.3. For each of the lightscenes, valuescan be preset for the actuator groupson their own parameter page.4. The rockers that are not used forlightscenes are still available forswitching, dimming or shutter control.The parameter value “no function”must be selected for unassignedrockers.If a rocker is used for recallinglightscenes, the LED indicates whichside of the rocker has been pressed. Itglows red when the left side is pressedand glows green when the right side ispressed. If several rockers are used,the LED of the rocker which was lastpressed lights up.Application example:A dimmable lamp is installed in a hotelroom in the sleeping area togetherwith a dimmable lamp in the entrance.There is also a reading light by thebed. The room can be darkened withan electrically driven blind. The light inthe adjoining bathroom can also bedimmed.From the door, it should be possible tooperate the dimmable lamps in thesleeping area and entrance togetherbut operate the light in the bathroomseparately. It should also be possibleto operate the blind.Four lightscenes can be recalled via apush button action:1.Switch all the lights to almostmaximum brightness and raise theblind to clean the room.2.Switch off all the lights and raise theblind when leaving the room.3.Dim the lights in the bathroom aandentrance to semi-brightness to lightthe way.4.Dim all the lights except for thebathroom light to 80% brightnessand lower the blind in the evening.From the bed, it should be possible toswitch the lights in the sleeping areaand entrance together but dim thereading light separately. It should alsobe possible to operate the blind.Four lightscenes should be recalledvia a push button action:1.Dim the lights in the bathroom andentrance to semi-brightness to lightthe way during the night and switchoff the reading light.2.Switch off all the lights for sleeping.3.Switch on all the lights withmaximum brightness for waking up.4.Dim the lights to a brightness valueof 60%.Two 5-fold Busch-triton ® switchsensors are used, each with adimming actuator/sensor FM togetherwith two switch/dim actuators and ashutter actuator. The dimming actuator/sensor FM at the door controls thelights in the entrance while thedimming actuator/sensor FM by thebed controls the reading light.March 2003 8 - 131
ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6324-xxThe Busch-triton ® switch sensor at thedoor has the following parametersettings:Number of lightscenes:4Function of auxiliary push button:no functionOperation mode of rocker 1:Dimming sensorOperation mode of rocker 2:Dimming sensorOperation mode of rocker 3:Shutter sensorOperation mode of rocker 4:Rocker is assigned to twolightscenesOperation mode of rocker 5:Rocker is assigned to twolightscenesRocker is assigned to IR push button:no IRType of actuator group A:Dimming actuator (8 bit)Type of actuator group B:Dimming actuator (8 bit)Type of actuator group C:Dimming actuator (8 bit)Type of actuator group D:Dimming actuator (8 bit)Type of actuator group E:Switch or shutter actuator (1 bit)The lightscenes are defined as follows:Lightscene 1: Base lightingActuator group A: 90%,Actuator group B: 90%,Actuator group C: 90%,Actuator group D: 90%,Actuator group E: UPLightscene 2: OFFActuator group A: 0%,Actuator group B: 0%,Actuator group C: 0%,Actuator group D: 0%,Actuator group E: UPLightscene 3: Passageway lightingActuator group A: 50%,Actuator group B: 50%,Actuator group C: 0%,Actuator group D: 0%,Actuator group E: UPLightscene 4: EveningActuator group A: 80%,Actuator group B: 0%,Actuator group C: 80%,Actuator group D: 80%,Actuator group E: UPThe 1 bit and 4 bit communicationobjects of rocker 1 are linked with theobjects of the dimming actuator/sensorand the dimming actuator for thesleeping area.The two objects of rocker 2 are linkedwith the corresponding objects of theactuators that control the lights in thebathroom.The transmit flags are set for theswitching objects of the dimmingactuators. The status LEDs can also becontrolled when the lightscenes arerecalled. It should be ensured that theparameter “Status response to objectof brightness value” is set to “yes”.The two objects of rocker 3 are linkedwith the corresponding objects of theshutter actuator.The 1 byte object of actuator group A islinked with the 1 byte object of thedimming actuator/sensor at the door.The 1 byte communication objects ofactuator groups B and C are linkedwith the 1 byte objects of the dimmingactuators. Actuator group B is for thedimming actuator in the bathroomwhile actuator group C is for thedimming actuator in the sleeping area.The 1 byte communication object ofactuator group D is linked with the1 byte object of the dimming actuator/sensor by the bed.The 1 bit communication object ofactuator group E is linked with theobject of the shutter actuator thatraises and lowers the blind.8 - 132 March 2003
Page 1 and 2:
ABB i-bus ® EIBSwitch/dim actuator
Page 3 and 4:
ABB i-bus ® EIBSwitch/dim actuator
Page 5 and 6: ABB i-bus ® EIBSwitch/dim actuator
Page 55: ABB i-bus ® EIBSwitch/dim actuator
show all

ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?