ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

More documents

Recommendations

Info

ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6324-xxIR Switch Dim Shutter Lightscene /4Selection in ETS2– ABBPush Button tritonPush button, 5-fold for 1SDAThe application program is intendedfor the 5-fold Busch-triton ® switchsensor application module inconnection with a switch/dim actuatorFM.The Busch-triton ® switch sensor canbe used for switching, dimming andshutter control as well as forcontrolling lightscenes. Variousparameters and communicationobjects are available for the fiverockers depending on the setting inthe parameter “Number oflightscenes”.Four lightscenes are available in thedefault setting which can be recalledvia rockers 4 and 5.The rockers of the Busch-triton ® switchsensor that are not used for lightscenecontrol each have the same set ofparameters. With the parameter“Operation mode of rocker”, the basicswitching, dimming and shuttercontrol functions can be selected.Depending on this setting, differentparameters and objects are availablefor the rockers. There is a commonparameter “Push button actioninterpreted as long from” for all therockers that are used for dimming orshutter control. Normally, the switchsensor detects a long push buttonaction if a rocker is pressed for longerthan 420 ms.BacklightingThe backlit text fields display thefunctions of the rockers even in thedark. Using the communication object“Backlighting/LED”, the backlightingand status LEDs can be switched onor off if required.The auxiliary push button can also beused for manual switching. To do so,the parameter “Function of auxiliarypush button” must be set to“Backlighting and LED on/off”. Whenthe auxiliary push button is pressed,not only is the lighting of the switchsensor switched on or off but atelegram is sent via thecommunication object “Backlighting/LED”. It is therefore possible to switchon the lighting for several Buschtriton® switch sensors at the same timevia a common group address.By default, the backlighting switcheson after bus voltage recovery. This canalso be changed via the parameter“Behaviour of backlighting at busrecovery”.Dimmer outputThe dimmer output has the threecommunication objects “Switching”,“Rel. dimming” and “Brightness value”.It can thus also be controlled by othersensors via the EIB. If a rocker of theBusch-triton ® switch sensor isparameterised as a dimming sensorand the communication objects of therocker are linked with those of thedimming actuator via a group address,the actuator can also be operatedlocally.If the switch sensor is dimmed up fromthe OFF state or switched on with abrightness value, it sends its newstatus on the EIB in the basic setting.This function is required for example toswitch on status LEDs.If the parameter “Status response to...”is set to “no”, this function can also beswitched off.On receipt of an “On” telegram at the1 bit communication object, theactuator can switch on with minimumor maximum brightness. The value canbe predefined with the parameter“Switch on with”.Using the parameters “Time base ...”and “Factor for dimming range”, it ispossible to set the period which thedimming actuator requires to dim up ordown fully once.IRIn addition to using the rockers, theBusch-triton ® switch sensor can alsobe controlled remotely via an infraredhand-held transmitter. The five rockersand the auxiliary push button can beassigned to the white or blue infraredarea of the hand-held transmitter. Therelevant setting must then be selectedvia the slide switch on the transmitter.The MEMO button of the transmittercorresponds to the function of theauxiliary push button of the Buschtriton® switch sensor.March 2003 8 - 129
ABB i-bus ® EIBSwitch/dim actuator, FMType: 6114 U-500 + 6324-xxSwitchIn the default setting of the Buschtriton® switch sensor, there is a 1 bitcommunication object available forswitching for each of the rockers thatare not assigned lightscenes. Forspecial applications, the parameter“Number of switch functions” can beset so that each rocker has twocommunication objects.The parameter “Working mode of therocker” determines which value theswitch sensor sends when the left orthe right side of the rocker is pressed.DimIf the operation mode of the rocker isset to “Dimming sensor”, the rockerhas the communication objects“Rocker ... -short” for switching and“Rocker ... -long” for dimming.When carrying out a switchingoperation, the rocker can either bepressed briefly on the left, on the rightor in the middle. The switch sensoralways toggles in this case.For dimming, it is determined via theparameter “Dimming direction” whichside of the rocker must be pressed andheld down in order to dim up or down.When the rocker is released, theswitch sensor sends the telegram“Stop dimming”.ShutterIf the operating mode of the rocker isset to “Shutter sensor”, the switchsensor sends “Move shutter up/down”telegrams when the left or right side ofthe rocker is pressed for a long period.After a short operation anywhere onthe rocker, it sends telegrams forstopping the shutter movement or forstepwise louvre adjustment.The parameter “Shutter direction”determines which side of the rockermust be pressed in order to moveupwards or downwards.LEDIf the backlighting of the text fields isswitched on, the LEDs can be selectedfor use either as an orientation light orfor status display using the parameter“Operation mode of LED”.In the case of LEDs that are used forstatus display, it is possible to setwhich colour (red or green) isassigned to the object values “0” or “1”.The LEDs that are used as anorientation light can either always lightup red or always green or they can beswitched off.8 - 130 March 2003
Page 1 and 2:
ABB i-bus ® EIBSwitch/dim actuator
Page 3 and 4: ABB i-bus ® EIBSwitch/dim actuator
Page 53: ABB i-bus ® EIBSwitch/dim actuator
show all

ABB i-busÂ® EIB Switch/dim actuator, FM Type: 6114 U-500

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?