Conventional Systems Technical Manual - Alcad

ELECTRONIC VIDEO DOOR ENTRY INSTALLATIONS.ELECTRONIC CALL.CONVENTIONAL 6+N+COAXIAL SYSTEMSTANDARD INSTALLATION IN BUILDINGNothing works.Check the mains voltage in the power supplies. Check thatthe voltage between V~, of the power supply is 12 ± 10%Vac. Check wether there is a short circuit and fix it. Disconnectthe power supply for 1 minute and then connect it up again.If it still doesn't work, disconnect all the power supplyV~, terminals, and check that the voltage between V~, is12 ± 10% Vac, if it is not, then there may be something wrongwith the power supply.The card holders don't light up.Check that the voltage between V~, of the power supply is12 ± 10% Vac.Check that the voltage between 9,10 in theaudio unit, with the lighting push button activated, is 12 ±10%Vac. Check wether the lamp has burnt out.The lighting push button pilot does not light up.Check that the voltage between the V~, of the audio unitis 12 ± 10% Vac. If the voltage is correct, there may be somethingwrong with the audio unit.The call tone doesn’t ring on any monitor.Check that the voltage between 7,2 in the audio unit, withoutpressing the push button, is 14.5 ± 10% Vdc. Check the connectionbetween 7 in the audio unit and the push buttons.Check connection 2 from the audio unit to the monitors. If youcannot find the fault, there may be something wrong with theaudio unit.The call tone doesn’t ring in a monitor.Check that the handset is not off the hook. Check the connectionbetween the connection bracket and the monitor.Check connections 5,2 from the conection bracket to theentrance panel. Check the push-button connection on the audiounit. If you cannot find the fault, there may be something wrongwith monitor or the panel push-button.You cannot hear the call confirmation on theentrance panel.Check that you can hear the monitors on the entrance panel.Check that the call tone rings on the monitors. If you cannotfind the fault, there may be something wrong with the audiounit.No monitor/telephone can be heard from theentrance panel.Check connections 3,2 from the audio unit to all the monitors.Check the volume control on the panel. If you cannot findthe fault, there may be something wrong with the audio unit.One monitor/telephone cannot be heard from theentrance panel.Check connections 3,2 from the connection bracket/telephoneto the audio unit. If you cannot find the fault, there may besomething wrong with the connection bracket/telephone or themonitor.You cannot hear an entrance panel on any monitor/telephone.Check connections 4,2 from the audio unit to all the monitors.Check the volume control on the monitors on the entrancepanel. If you cannot find the fault, there may be somethingwrong with the audio unit.You cannot hear the entrance panel on a monitor/telephone.Check connections 4,2 from the connection bracket to theaudio unit. If you cannot find the fault, there may be somethingwrong with the monitor.The sound produces feedback.Lower the sound level using the volume control on the audiounit. If the feedback persists, remove the J2 jumper and repeatthe adjustment.The electric lock doesn’t work.Check that the voltage between 1,2 in the audio unit, withoutpressing the lock release button, is 5 ± 10% Vdc. Check thatthe voltage between 11,12 in the audio unit, when you pressthe lock release button, is 12 ± 10% Vac. If you cannot findthe fault, the electric lock may be broken.The video system does not work in any monitor:auto switch-on, screen doesn´t come on when receivinga call,..Check the mains voltage in the power supply unit that feedsthe monitors. Check that the voltage of the power supply between+, - is 15 ± 10% Vdc. Check if there's a short circuit andrectify it. Disconnect the power supplies supply for 1 minuteand reconnect it. If the breakdown continues, disconnect all the+, - terminals from the power supply unit and check that voltagebetween +, - is 15 ± 10% Vdc. If it's not correct, there maybe something wrong with the power supply.Video system does not work in one monitor: autoswitch-on, screen doesn´t come on when receiving acall,..Check that the ON/OFF switch for the video is in ON position(on the left). Check that the red led of the monitor is on.Check the connection between the connection bracket and themonitor. Check that the voltage between +, - of the connectionbracket is 14 ± 15% Vdc. If failure cannot be found, there maybe something wrong with the monitor.300