M300 Owner's Manual-English - Lexicon

More documents

Recommendations

Info

300 V3.0 Owner's ManualProgrammingParameter GlidesLexiconParameter glides can be a verypoweful feature. When you select a parameterglide (PA,PB, or PS) as type of automation change, the display will update anddisplay three entries; Parameter Selection (RTIM, PDLY, DLY1,FBK1...), finalparameter value (12.5s, 125m, 225m, 45%...), and the frame duration (25Fr) ofthe glide. The keys beneath each display entry allow you to select the functionfor Soft knob programming of the parameter glides.All parameter glides are based on the current Setup and effect which loaded.Example:Let’s say at the end of a scene, we want the Reverb Time to increase from itspreset value to 15 seconds. We want this glide to take 100 frames. At the sametime, we want the Input parameter to glide from its Setup value to OFF over thesame amount of time.Suppose the current Setup and Effect is Dance Hall, then all of the parametersin the Setup and effect can Be glided.The Event List up to the glide might look something like this:Edit #01 00 : 59 : 27 : 00S: Large HallEdit #02 01 : 00 : 15 : 00S: Dance HallEdit #03 01 : 00 : 21 : 07**: New EventYou will need to make a copy of event 03 (because you want 2 parameter glides)into the list, then edit both entries.6-6
Time Code OperationFrom the main time code menu, select “ADD”. Now select the edit event numberby pressing the key directly above “#”. Use the Soft knob to selet “#3”, then pressSTORE. This makes a complete copy of event # 3 and places it into slot #4. Notethat Event #3 and Event #4 now have the same time code adress.PRESS CNTRL to return to the main time code menu.Press EDIT, then select Edit #3. Now, press the key directly below “**” and usethe Soft knob to program PA:(parameter,Machine A).Press the next button to the right to use the Soft knob to program the actualparameter. Turn the Soft knob until the “RTIM” is displayed.Press the next button to the right to use the Soft knob to select the final reverbtime. Adjust the value as close to 15 seconds as possible.Finally, press the next button to the right. Turn the Soft knob clockwise to enterframe duration values. (100 Fr will equal approximately 3 seconds.)Press STORE. Event #3 should look like this:Edit #03 01 : 00 : 21 : 05PA:RTIM->14.1s 100FrPress the key directly above “#”, and repeat the above steps so that the displaylooks like this:Edit #04 01 : 00 : 21 : 05PS: ALVL->Off 100FrParameter glides which have been programmed into the Event List will beviewed singly, as the event happens. If you are VIEWing two or more glideswhich happen to be programmed for the same time code (as in the exampleabove), only the last entry will be displayed.6-7
Page 2 and 3:
Unpacking and InspectionAfter unpac
Page 4 and 5:
Contents, cont'd. 4. The Algorithms
Page 6 and 7:
Congratulations on your purchase of
Page 8 and 9:
Installing the 300Installing the300
Page 10 and 11:
Installing the 300The Rear PanelTim
Page 12 and 13:
Installing the 300CablesFor best pe
Page 14 and 15:
Installing the 300ConfigurationsCon
Page 16 and 17:
PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHIns
Page 18 and 19:
PUSHPUSHPUSHPUSHInstalling the 300A
Page 20 and 21:
300 V 3.0 Owner's ManualLexiconTerm
Page 22 and 23:
300 V 3.0 Owner's ManualLexiconThe
Page 24 and 25:
300 V 3.0 Owner's ManualLexiconOver
Page 26 and 27:
300 V 3.0 Owner's ManualLexiconSETU
Page 28 and 29:
System Operation3System Operation3-
Page 30 and 31:
System OperationIf you wish to chan
Page 32 and 33:
System OperationNOTE: Most studio a
Page 34 and 35:
System OperationWhen working in a f
Page 36 and 37:
System OperationSetup Select mode a
Page 38 and 39:
System OperationTo enter Setup Sele
Page 40 and 41:
System OperationSetup Edit mode is
Page 42 and 43:
System OperationWhen you have made
Page 44 and 45:
System OperationPage FiveNaming the
Page 46 and 47:
System OperationHere again, turning
Page 48 and 49:
System OperationSoft knob patches a
Page 50 and 51:
System OperationThe MIDI Control pa
Page 52 and 53:
System OperationPage FiveSCMS ModeS
Page 54 and 55:
System OperationSrc : SET Large Hal
Page 56 and 57:
300 V 3.0 Owner's ManualSingle Setu
Page 58 and 59:
300 V 3.0 Owner's ManualRandom Hall
Page 60 and 61:
300 V 3.0 Owner's ManualLexiconRand
Page 62 and 63:
300 V 3.0 Owner's ManualLexiconRand
Page 64 and 65:
300 V 3.0 Owner's ManualRLVL (Rever
Page 66 and 67:
300 V 3.0 Owner's ManualLexiconRich
Page 68 and 69:
300 V 3.0 Owner's ManualLexiconFBK1
Page 70 and 71:
300 V 3.0 Owner's ManualLexiconSter
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
300 V 3.0 Owner's ManualDual Delays
Page 80 and 81:
300 V 3.0 Owner's ManualLexiconSpli
Page 82 and 83: 300 V 3.0 Owner's ManualSPRD (Sprea
Page 84 and 85: 300 V 3.0 Owner's ManualLexiconDLYD
Page 86 and 87: 300 V 3.0 Owner's ManualCompressorP
Page 88 and 89: 300 V 3.0 Owner's ManualLexiconSmal
Page 90 and 91: 300 V 3.0 Owner's ManualLexiconin p
Page 92 and 93: 300 V 3.0 Owner's ManualThe Setup P
Page 94 and 95: 300 V 3.0 Owner's ManualLexiconSing
Page 96 and 97: 300 V 3.0 Owner's ManualSplit Setup
Page 98 and 99: 300 V 3.0 Owner's ManualLexiconP208
Page 110 and 111: 300 V 3.0 Owner's ManualSplit Setup
Page 112 and 113: 300 V 3.0 Owner's ManualLexiconEP #
Page 114 and 115: 300 V 3.0 Owner's ManualLexiconEP #
Page 116 and 117: 300 V 3.0 Owner's ManualLexiconEffe
Page 118 and 119: 300 V 3.0 Owner's ManualEffect Pres
Page 128 and 129: 300 V3.0 Owner's ManualLexiconUsing
Page 130 and 131: 300 V3.0 Owner's ManualSnapping eve
Page 134 and 135: 300 V3.0 Owner's ManualThings to Co
Page 136 and 137: 300 Event List300 V3.0 Owner's Manu
Page 138 and 139: 300 V 3.0 Owner's ManualLexiconThe
Page 140 and 141: 300 V 3.0 Owner's ManualLexiconDyna
Page 142 and 143: 300 V 3.0 Owner's ManualReal-time M
Page 144 and 145: 300 V 3.0 Owner's ManualMIDI Dumps
Page 146 and 147: 300 V 3.0 Owner's ManualTroubleshoo
Page 148 and 149: MIDI Implementation Data9MIDI Imple
Page 150 and 151: Specifications10300 Specifications1
Page 152 and 153: SpecificationsAnalog Input to Analo
show all

M300 Owner's Manual-English - Lexicon

Create successful ePaper yourself

Delete template?

Save as template?