M300 Owner's Manual-English - Lexicon

More documents

Recommendations

Info

300 V 3.0 Owner's ManualTroubleshootingLexiconThis chapter is intended primarily to help you recognize some common errorstates which can be corrected from the 300 front panel, or by simple means suchas cable replacement. Any error states which are not covered here should bereferred to your local dealer for service by a qualified technician.Low VoltageIn a low-voltage, or "brown-out" condition, the 300 will freeze in its current state.None of the controls will have any effect. When power returns to a normal levelthe unit will reset itself as though it had just been powered on. If the unit doesnot reset itself, turn the power OFF, then ON to resume normal operation.OverheatingTemperature extremes may cause the 300 to exhibit unpredictable behavior. Ifthe unit as been subjected to temperatures below 32°F (0°C) or above 95°F(35°C), it should be turned off and allowed to return to normal temperaturebefore use. The unit may be damaged by exposure to temperatures below -22°F(-30°C) or above 167°F (75°C), or by exposure to humidity in excess of 95%. Ifa unit exposed to such conditions fails to operate after it returns to a normaloperating temperature, contact your local service representative.Common MIDIProblemsThe 300 doesn't respond to MIDI Program Changes.Check the PARAM MIDI channel on the MIDI Control page in Control mode andcheck the Table Mode setting on the same page. The Table Mode should be setto FIX or TABLE. Also check MIDI In/Out connections between the units.The 300 doesn't respond to Controller messages when using DynamicMIDI ® .Check the PARAM MIDI Channel number on the MIDI Control page in Controlmode and check the patches in MOD Edit mode. Also check MIDI In/Outconnections between the units.The 300 doesn't respond to SysEx commands.Check the SYSTEM MIDI Channel on the MIDI Control page in Control mode.The 300 does not send MIDI parameter changes.Check the Automation mode on the MIDI Control page in Control mode. Thisshould be set to SYS EX or NON-REGISTERED PARAMS.8-2
TroubleshootingThe 300 does not change effects to incoming time code.Check your cable connections and the setting of the Event List mode in Controlmode. Also check the signal level of the incoming time code. If it is too low, the300 may not respond.Common Time CodeProblemsThe 300 will not lock to the incoming time code.Check the signal level of the incoming time code. If the level is too high or too low,the 300 may not lock to the signal. Also check the wiring of the time code cable.The time code input on the 300 is electronically balanced and, if the cable is notwired with this in mind, the 300 may not lock to the signal.The 300 changes effects too late.Trim the time code values using the Edit function on the Time Code Event Listpage in Control mode.The 300 will not lock onto an incoming digital signal.Check the cables that you are using. If the signal is coming in through the RCAconector, cable length must be kept to a minimum. If you are using the XLR input,remember that this is a transformer-balanced input, and the cable must be wiredwith this in mind. DO NOT USE ANALOG AUDIO CABLE TO CONNECTDIGITAL AUDIO.Common DigitalInterfacing ProblemsWhen using the ANA+DIG input mode, there is no audio output.If you are using this mode and you are not sending a digital signal to the 300,audio may not pass through the system. To correct this, choose the ANALOGmode, or enter Effect Edit mode and turn the digital input level all the way down.The meters do not show any incoming signal.The meters may be set to read the wrong inputs. Use the Meter page in SetupEdit mode to select the inputs you are using.8-3
Page 2 and 3:
Unpacking and InspectionAfter unpac
Page 4 and 5:
Contents, cont'd. 4. The Algorithms
Page 6 and 7:
Congratulations on your purchase of
Page 8 and 9:
Installing the 300Installing the300
Page 10 and 11:
Installing the 300The Rear PanelTim
Page 12 and 13:
Installing the 300CablesFor best pe
Page 14 and 15:
Installing the 300ConfigurationsCon
Page 16 and 17:
PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHIns
Page 18 and 19:
PUSHPUSHPUSHPUSHInstalling the 300A
Page 20 and 21:
300 V 3.0 Owner's ManualLexiconTerm
Page 22 and 23:
300 V 3.0 Owner's ManualLexiconThe
Page 24 and 25:
300 V 3.0 Owner's ManualLexiconOver
Page 26 and 27:
300 V 3.0 Owner's ManualLexiconSETU
Page 28 and 29:
System Operation3System Operation3-
Page 30 and 31:
System OperationIf you wish to chan
Page 32 and 33:
System OperationNOTE: Most studio a
Page 34 and 35:
System OperationWhen working in a f
Page 36 and 37:
System OperationSetup Select mode a
Page 38 and 39:
System OperationTo enter Setup Sele
Page 40 and 41:
System OperationSetup Edit mode is
Page 42 and 43:
System OperationWhen you have made
Page 44 and 45:
System OperationPage FiveNaming the
Page 46 and 47:
System OperationHere again, turning
Page 48 and 49:
System OperationSoft knob patches a
Page 50 and 51:
System OperationThe MIDI Control pa
Page 52 and 53:
System OperationPage FiveSCMS ModeS
Page 54 and 55:
System OperationSrc : SET Large Hal
Page 56 and 57:
300 V 3.0 Owner's ManualSingle Setu
Page 58 and 59:
300 V 3.0 Owner's ManualRandom Hall
Page 60 and 61:
300 V 3.0 Owner's ManualLexiconRand
Page 62 and 63:
300 V 3.0 Owner's ManualLexiconRand
Page 64 and 65:
300 V 3.0 Owner's ManualRLVL (Rever
Page 66 and 67:
300 V 3.0 Owner's ManualLexiconRich
Page 68 and 69:
300 V 3.0 Owner's ManualLexiconFBK1
Page 70 and 71:
300 V 3.0 Owner's ManualLexiconSter
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
300 V 3.0 Owner's ManualDual Delays
Page 80 and 81:
300 V 3.0 Owner's ManualLexiconSpli
Page 82 and 83:
300 V 3.0 Owner's ManualSPRD (Sprea
Page 84 and 85:
300 V 3.0 Owner's ManualLexiconDLYD
Page 86 and 87:
300 V 3.0 Owner's ManualCompressorP
Page 88 and 89:
300 V 3.0 Owner's ManualLexiconSmal
Page 90 and 91:
300 V 3.0 Owner's ManualLexiconin p
Page 92 and 93:
300 V 3.0 Owner's ManualThe Setup P
Page 94 and 95:
300 V 3.0 Owner's ManualLexiconSing
Page 96 and 97: 300 V 3.0 Owner's ManualSplit Setup
Page 98 and 99: 300 V 3.0 Owner's ManualLexiconP208
Page 110 and 111: 300 V 3.0 Owner's ManualSplit Setup
Page 112 and 113: 300 V 3.0 Owner's ManualLexiconEP #
Page 114 and 115: 300 V 3.0 Owner's ManualLexiconEP #
Page 116 and 117: 300 V 3.0 Owner's ManualLexiconEffe
Page 118 and 119: 300 V 3.0 Owner's ManualEffect Pres
Page 128 and 129: 300 V3.0 Owner's ManualLexiconUsing
Page 130 and 131: 300 V3.0 Owner's ManualSnapping eve
Page 132 and 133: 300 V3.0 Owner's ManualProgrammingP
Page 134 and 135: 300 V3.0 Owner's ManualThings to Co
Page 136 and 137: 300 Event List300 V3.0 Owner's Manu
Page 138 and 139: 300 V 3.0 Owner's ManualLexiconThe
Page 140 and 141: 300 V 3.0 Owner's ManualLexiconDyna
Page 142 and 143: 300 V 3.0 Owner's ManualReal-time M
Page 144 and 145: 300 V 3.0 Owner's ManualMIDI Dumps
Page 148 and 149: MIDI Implementation Data9MIDI Imple
Page 150 and 151: Specifications10300 Specifications1
Page 152 and 153: SpecificationsAnalog Input to Analo
show all

M300 Owner's Manual-English - Lexicon

Create successful ePaper yourself

Delete template?

Save as template?