M300 Owner's Manual-English - Lexicon

More documents

Recommendations

Info

System OperationHere again, turning the Soft knob will adjust the selected parameter over itsentire range; the soft buttons will select other parameters for adjustment. ThePAGE UP and PAGE DOWN keys are used to access various pages ofadditional parameters which can then be edited via the Soft knob.When changes have been made on a page, and you move to a new page, theprevious edits remain intact. However, when a new effect is loaded, edits will belost unless you have stored the edited effect in a register.In Split Setups, effects are loaded into both Machine A and Machine B. Use theMACH button to toggle between Machine Effects.The 300 has 50 registers available to store edited versions of the preset effects.After you have made the changes you want to an effect's parameters, you canstore the changed version into an effect register simply by pressing STORE.Thefollowing display will appear:Naming andStoring EffectsSrc: EFFA *3VoiceDlyDst R1 AvailableThe display will show the name of the current effect (in this example, *#VoiceDly,running in Machine A), and a register location.Press the button directly beneath "R#" to select a different register with the Softknob. Press STORE again to complete the operation. Once registers are filled,they can be selected and loaded exactly like presets. You can edit parametersin a register, and store the results in the same register or another register.)When you store a register, the edited effect still has the same name as theoriginal effect. To avoid confusion, you can assign names to registers. Forconvenience, a naming page is included in Effect Edit mode. To rename aregister, follow the same procedure described for naming a Setup.3-19
300 V 3.0 Owner's ManualMod Edit ModeLexiconMod Edit mode is used to create or modify Dynamic MIDI ® patches. To useDynamic MIDI ® , you assign a MIDI controller or an event to a setup parameteror an effect parameter, using the patch parameters found on the pages in ModEdit. (Two pages for Setup patches are available in Setup Edit mode.) Fourparameter patch pages are available at any one time in Mod Edit mode. Thepages will be for Machine A or Machine B, depending on the type of setupcurrently running, and on the machine currently selected.Each of the four available patch pages shows the following parameters:Patch # 1A DEST VALUEOffCntlr- 0ModWheelBreathCntlr-3FootPedalPortaTimeVolumeCntlr-9PanExpressionCntlr-12-15GP Cntlr-1-4Cntlr-20-31SustainPortaSwSostenSwSoftPedalSwitch-68-79GP Cntlr-5-8Sitch-84-95PitchWheelAfterTouchLastNoteLastVelMidiClockKnob->L-MeterR-MeterLFO-1Available "Source" selectionsSOURCE THRS SCALEDestination: This is used to select the effect parameter that the MIDI controlleris patched to. The available parameters are based on the algorithm that you arecurrently running.Value: This is used to set the initial value of the parameter that you arecontrolling. This is provided as a convenience so that you do not have to go intoEffect Edit mode to view the available parameters of the running algorithm.Source: This is used to select the MIDI controller, or event, that will control aneffect parameter in the 300. The list contains the selections shown to the left.Threshold: This is used to set thecontroller value below which the controller willnot have an effect on the parameter.Scale: This is used to set the effective control range of the MIDI controller.Scaling can be set from -200% to +200%. When Scale is set to 100%, the fullrange of the MIDI controller will cover the full range of the selected parameter.Setting a negative value will cause the 300 to reduce the setting of the parameteras the controller increases.You can store any patches you create with the Effect simply by pressing STORE,selecting a register number with the Soft knob, and then pressing STORE again.Note: Be extremely careful when creating patches while a MIDI deviceis connected. If you accidentally send a MIDI Program Change beforesaving the patches in a register, they will be lost. To avoid thispossibility, you may want to set the MIDI Master Channel (in ControlMode) to OFF, or unplug the MIDI cable from the 300's rear-panel MIDIIN connector.3-20
Page 2 and 3: Unpacking and InspectionAfter unpac
Page 4 and 5: Contents, cont'd. 4. The Algorithms
Page 6 and 7: Congratulations on your purchase of
Page 8 and 9: Installing the 300Installing the300
Page 10 and 11: Installing the 300The Rear PanelTim
Page 12 and 13: Installing the 300CablesFor best pe
Page 14 and 15: Installing the 300ConfigurationsCon
Page 16 and 17: PUSHPUSHPUSHPUSHPUSHPUSHPUSHPUSHIns
Page 18 and 19: PUSHPUSHPUSHPUSHInstalling the 300A
Page 20 and 21: 300 V 3.0 Owner's ManualLexiconTerm
Page 22 and 23: 300 V 3.0 Owner's ManualLexiconThe
Page 24 and 25: 300 V 3.0 Owner's ManualLexiconOver
Page 26 and 27: 300 V 3.0 Owner's ManualLexiconSETU
Page 28 and 29: System Operation3System Operation3-
Page 30 and 31: System OperationIf you wish to chan
Page 32 and 33: System OperationNOTE: Most studio a
Page 34 and 35: System OperationWhen working in a f
Page 36 and 37: System OperationSetup Select mode a
Page 38 and 39: System OperationTo enter Setup Sele
Page 40 and 41: System OperationSetup Edit mode is
Page 42 and 43: System OperationWhen you have made
Page 44 and 45: System OperationPage FiveNaming the
Page 48 and 49: System OperationSoft knob patches a
Page 50 and 51: System OperationThe MIDI Control pa
Page 52 and 53: System OperationPage FiveSCMS ModeS
Page 54 and 55: System OperationSrc : SET Large Hal
Page 56 and 57: 300 V 3.0 Owner's ManualSingle Setu
Page 58 and 59: 300 V 3.0 Owner's ManualRandom Hall
Page 60 and 61: 300 V 3.0 Owner's ManualLexiconRand
Page 62 and 63: 300 V 3.0 Owner's ManualLexiconRand
Page 64 and 65: 300 V 3.0 Owner's ManualRLVL (Rever
Page 66 and 67: 300 V 3.0 Owner's ManualLexiconRich
Page 68 and 69: 300 V 3.0 Owner's ManualLexiconFBK1
Page 70 and 71: 300 V 3.0 Owner's ManualLexiconSter
Page 78 and 79: 300 V 3.0 Owner's ManualDual Delays
Page 80 and 81: 300 V 3.0 Owner's ManualLexiconSpli
Page 82 and 83: 300 V 3.0 Owner's ManualSPRD (Sprea
Page 84 and 85: 300 V 3.0 Owner's ManualLexiconDLYD
Page 86 and 87: 300 V 3.0 Owner's ManualCompressorP
Page 88 and 89: 300 V 3.0 Owner's ManualLexiconSmal
Page 90 and 91: 300 V 3.0 Owner's ManualLexiconin p
Page 92 and 93: 300 V 3.0 Owner's ManualThe Setup P
Page 94 and 95: 300 V 3.0 Owner's ManualLexiconSing
Page 96 and 97:
300 V 3.0 Owner's ManualSplit Setup
Page 98 and 99:
300 V 3.0 Owner's ManualLexiconP208
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
300 V 3.0 Owner's ManualSplit Setup
Page 112 and 113:
300 V 3.0 Owner's ManualLexiconEP #
Page 114 and 115:
300 V 3.0 Owner's ManualLexiconEP #
Page 116 and 117:
300 V 3.0 Owner's ManualLexiconEffe
Page 118 and 119:
300 V 3.0 Owner's ManualEffect Pres
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
300 V3.0 Owner's ManualLexiconUsing
Page 130 and 131:
300 V3.0 Owner's ManualSnapping eve
Page 132 and 133:
300 V3.0 Owner's ManualProgrammingP
Page 134 and 135:
300 V3.0 Owner's ManualThings to Co
Page 136 and 137:
300 Event List300 V3.0 Owner's Manu
Page 138 and 139:
300 V 3.0 Owner's ManualLexiconThe
Page 140 and 141:
300 V 3.0 Owner's ManualLexiconDyna
Page 142 and 143:
300 V 3.0 Owner's ManualReal-time M
Page 144 and 145:
300 V 3.0 Owner's ManualMIDI Dumps
Page 146 and 147:
300 V 3.0 Owner's ManualTroubleshoo
Page 148 and 149:
MIDI Implementation Data9MIDI Imple
Page 150 and 151:
Specifications10300 Specifications1
Page 152 and 153:
SpecificationsAnalog Input to Analo
show all

M300 Owner's Manual-English - Lexicon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?