VFD-F (CURVE).cdr

More documents

Recommendations

Info

<strong>VFD</strong>-F Series13. For the single-phase rated AC drives, the AC power can be connected to any two of thethree input terminals R/L1, S/L2, T/L3. Note: This drive is not intended for the usewith single-phase motors.14. Route the power and control wires separately, or at 90°angle to each other.15. If a filter is required for reducing EMI (Electro Magnetic Interference), install it as closeas possible to AC drive. EMI can also be reduced by lowering the Carrier Frequency.316. If the AC drive is installed in the place where a load reactor is needed, install the filterclose to U/T1, V/T2, W/T3, side of AC drive. Do not use a Capacitor or L-C Filter(Inductance-Capacitance) or R-C Filter (Resistance-Capacitance), unless approved byDelta.17. When using a GFCI (Ground Fault Circuit Interrupt), select current sensor with sensitivityof 200mA, and not less than 0.1-second detection to avoid nuisance tripping.18. To improve the input power factor, to reduce harmonics and provide protection from ACline disturbances (surges, switching spikes, short interruptions, etc.), AC line reactorshould be installed when the power supply capacity is 500kVA or more.19. There are highly sensitive MOS components on the printed circuit boards. Thesecomponents are especially sensitive to static electricity. To prevent damage to thesecomponents, do not touch these components or the circuit boards with metal objects oryour bare hands.DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 3-17
<strong>VFD</strong>-F Series3.6 Motor Operation Precautions1. When using the AC drive to operate a standard 3-phase induction motor, notice that theenergy loss is greater than for an inverter duty motor.2. Avoid running a standard induction motor at low speed. Under these conditions, themotor temperature may rise above the motor rating due to limited airflow produced bythe motor’s fan.3. When the standard motor operates at low speed, the output load must be decreased.4. If 100% output torque is desired at low speed, it may be necessary to use a special“inverter-duty” rated motor.3-18DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
Page 4 and 5: PrefaceThank you for choosing DELTA
Page 6 and 7: VFD-F Series5.3 Group 2: Operation
Page 9 and 10: VFD-F Series1.3 Series Number Expla
Page 11 and 12: 50mmFHUVFD-PU01RUN STOP JO G FWD RE
Page 13 and 14: VFD-F Series3.1 Basic Wiring Diagra
Page 15 and 16: VFD-F SeriesWiring for SINK mode an
Page 17 and 18: VFD-F SeriesTerminal Symbols Termin
Page 19 and 20: VFD-F Series7.5 HP to 20 HP(VFD055F
Page 21 and 22: POWERALARMVFD-F Series50 HP to 60 H
Page 23 and 24: VFD-F Series125 HP(VFD900F43A )R/L1
Page 25 and 26: VFD-F Series150 HP to 215 HP(VFD110
Page 27: VFD-F Series3.5 Wiring Notes: PLEAS
Page 31 and 32: VFD-F Series4.1.2 Description of th
Page 33 and 34: VFD-F Series4.1.3 Operation steps o
Page 35 and 36: VFD-F SeriesDisplay MessageDescript
Page 37 and 38: VFD-F SeriesCode AC Drive Status Ex
Page 39 and 40: VFD-F Series5.2 Group 1: Basic Para
Page 41 and 42: VFD-F SeriesOutput voltage01-0201-0
Page 43 and 44: VFD-F Series01-23 Accel/Decel time
Page 45 and 46: VFD-F Series02 - 02 Stop Method Fac
Page 47 and 48: VFD-F Series02 - 06 Line Start Lock
Page 49 and 50: VFD-F Series If this parameter is s
Page 51 and 52: VFD-F SeriesSetting FunctionsDescri
Page 53 and 54: VFD-F Series Setting 04: 0-10V = 0.
Page 55 and 56: VFD-F SeriesSetting Functions Descr
Page 57 and 58: VFD-F SeriesPlease refer to the fol
Page 59 and 60: VFD-F Series5.6 Group 5: Multi-step
Page 61 and 62: VFD-F SeriesExample 3 (Pr.05-15 = 3
Page 63 and 64: VFD-F Series05 - 17 Time Duration o
Page 65 and 66: VFD-F Series5.7 Group 6: Protection
Page 67 and 68: VFD-F Series This parameter selects
Page 69 and 70: VFD-F Series10 Over current during
Page 71 and 72: VFD-F Series5.8 Group 7: AC Drive a
Page 73 and 74: VFD-F Series Unsuitable setting val
Page 75 and 76: VFD-F SeriesOutput frequencyDC brak
Page 77 and 78: VFD-F SeriesMaster frequency comman
Page 79 and 80:
VFD-F Series08 - 18 Automatic Volta
Page 81 and 82:
VFD-F Series09 - 06 Communication O
Page 83 and 84:
VFD-F Series (7 , E , 1 : 9-04=0, 9
Page 85 and 86:
VFD-F Series• Command code: 03H,
Page 87 and 88:
VFD-F Series• Command code: 08H,
Page 89 and 90:
VFD-F Series3.4 CHK (check sum)ASCI
Page 91 and 92:
VFD-F Series3.5 Address ListThe con
Page 93 and 94:
VFD-F SeriesContent Address Functio
Page 95 and 96:
VFD-F Series5.11 Group 10: PID Cont
Page 97 and 98:
VFD-F Series This parameter determi
Page 99 and 100:
VFD-F Series In Pr. 11-01 set for 0
Page 101 and 102:
VFD-F Series If multi-function inpu
Page 103 and 104:
VFD-F SeriesFixed amountcirculation
Page 105 and 106:
VFD-F Series11 - 10 Treatment of Fi
Page 107 and 108:
This page intentionally left blankV
Page 109 and 110:
FaultNameVFD-F SeriesFault Descript
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
VFD-F SeriesParameters Functions Se
Page 117 and 118:
VFD-F SeriesGroup 2 Digital Output/
Page 119 and 120:
VFD-F SeriesGroup 3 Output Function
Page 121 and 122:
VFD-F SeriesGroup 4 Input Function
Page 123 and 124:
VFD-F SeriesGroup 5 Multi-step Spee
Page 125 and 126:
VFD-F SeriesGroup 6 Protection Func
Page 127 and 128:
VFD-F SeriesGroup 7 AC Drive and Mo
Page 129 and 130:
VFD-F SeriesGroup 9 Communication P
Page 131 and 132:
VFD-F SeriesGroup 10 PID ControlsPa
Page 133 and 134:
This page intentionally left blankV
Page 135 and 136:
VFD-F SeriesOther FunctionsProtecti
Page 137 and 138:
NOTEVFD-F Series1. Please select th
Page 139 and 140:
VFD-F SeriesB.3 AC Output Reactor R
Page 141 and 142:
VFD-F SeriesB.5 Fuse Specification
Page 143 and 144:
VFD-F SeriesDisplay MessageDescript
Page 145 and 146:
VFD-F SeriesPCB-SUPPORTPCB-SUPPORTS
Page 147 and 148:
VFD-F SeriesVFD015F23A 1.50 kW (2.0
Page 149 and 150:
VFD-F SeriesVFD150F23A 15.0 kW (20.
Page 151 and 152:
VFD-F SeriesVFD300F23A 30.0 kW (40.
Page 153 and 154:
VFD-F SeriesVFD1100F43CVFD1320F43AV
show all

VFD-F (CURVE).cdr

Create successful ePaper yourself

Delete template?

Save as template?