VFD-F (CURVE).cdr

More documents

Recommendations

Info

<strong>VFD</strong>-F Series02 - 09 Special Display Factory Setting: 00Settings 00: A displays output current of AC drive01: U displays DC-Bus voltage of AC drive02: E displays RMS of output voltage03: P displays feedback signal04: PLC display auto procedure state This parameter chooses the display on the keypad immediately following the “U” userdefined setting. “MODE” key will scroll from “F”, “H”, “U”, (Pr. 02-09), FWD, and back to “F”. Users may also use the “LEFT” key on the digital keypad to switch display content.02 - 10 User Defined Coefficient Factory Setting: 1.00Settings 0.01~160.00 Unit: 0.01 When this parameter is set, the “H “display value = actual output frequency of AC drive x02-10.5 If output frequency of AC drive is 90Hz, set 02-10 to 2.5. When H LED lights, the value onthe display is 225.00.02 - 11 Flying Start Factory Setting: 00Settings 00: Disable01: Enable (DC brake disabled) When the AC drive starts into a running motor (Flying Start), it may cause an over current onthe drive and may damage the motor. Using speed search upon start-up will allow the driveto slowly find the motor speed, smoothly take control of the motor, and bring it to commandspeed. If the Flying Start feature is enabled upon start-up, the DC brake 08-01 will be disabled.02 - 12 Flying Start Frequency Factory Setting: 00Settings 00: Begin search from Master Frequency Command01: Begin search from Maximum Frequency (Pr.01-00)02 - 13 Master Frequency Memory Setting Factory Setting: 01Settings 00: Do not remember the last known frequency01: Remember the last known frequencyDELTA ELECTRONICS, INC. ALL RIGHTS RESERVED 5-13
<strong>VFD</strong>-F Series If this parameter is set to 00: The AC drive will not store the last known master frequencycommand, after power is removed. If this parameter is set to 01: The AC drive will memorize the last known master frequencycommand after power off. Upon power up the last known frequency is displayed. After a fault, the AC drive will always remember the last know master frequency command. This feature is only enabled when Pr. 02-00 is set for 0 or 4.5-14DELTA ELECTRONICS, INC. ALL RIGHTS RESERVED
Page 4 and 5: PrefaceThank you for choosing DELTA
Page 6 and 7: VFD-F Series5.3 Group 2: Operation
Page 9 and 10: VFD-F Series1.3 Series Number Expla
Page 11 and 12: 50mmFHUVFD-PU01RUN STOP JO G FWD RE
Page 13 and 14: VFD-F Series3.1 Basic Wiring Diagra
Page 15 and 16: VFD-F SeriesWiring for SINK mode an
Page 17 and 18: VFD-F SeriesTerminal Symbols Termin
Page 19 and 20: VFD-F Series7.5 HP to 20 HP(VFD055F
Page 21 and 22: POWERALARMVFD-F Series50 HP to 60 H
Page 23 and 24: VFD-F Series125 HP(VFD900F43A )R/L1
Page 25 and 26: VFD-F Series150 HP to 215 HP(VFD110
Page 27 and 28: VFD-F Series3.5 Wiring Notes: PLEAS
Page 29 and 30: VFD-F Series3.6 Motor Operation Pre
Page 31 and 32: VFD-F Series4.1.2 Description of th
Page 33 and 34: VFD-F Series4.1.3 Operation steps o
Page 35 and 36: VFD-F SeriesDisplay MessageDescript
Page 37 and 38: VFD-F SeriesCode AC Drive Status Ex
Page 39 and 40: VFD-F Series5.2 Group 1: Basic Para
Page 41 and 42: VFD-F SeriesOutput voltage01-0201-0
Page 43 and 44: VFD-F Series01-23 Accel/Decel time
Page 45 and 46: VFD-F Series02 - 02 Stop Method Fac
Page 47: VFD-F Series02 - 06 Line Start Lock
Page 51 and 52: VFD-F SeriesSetting FunctionsDescri
Page 53 and 54: VFD-F Series Setting 04: 0-10V = 0.
Page 55 and 56: VFD-F SeriesSetting Functions Descr
Page 57 and 58: VFD-F SeriesPlease refer to the fol
Page 59 and 60: VFD-F Series5.6 Group 5: Multi-step
Page 61 and 62: VFD-F SeriesExample 3 (Pr.05-15 = 3
Page 63 and 64: VFD-F Series05 - 17 Time Duration o
Page 65 and 66: VFD-F Series5.7 Group 6: Protection
Page 67 and 68: VFD-F Series This parameter selects
Page 69 and 70: VFD-F Series10 Over current during
Page 71 and 72: VFD-F Series5.8 Group 7: AC Drive a
Page 73 and 74: VFD-F Series Unsuitable setting val
Page 75 and 76: VFD-F SeriesOutput frequencyDC brak
Page 77 and 78: VFD-F SeriesMaster frequency comman
Page 79 and 80: VFD-F Series08 - 18 Automatic Volta
Page 81 and 82: VFD-F Series09 - 06 Communication O
Page 83 and 84: VFD-F Series (7 , E , 1 : 9-04=0, 9
Page 85 and 86: VFD-F Series• Command code: 03H,
Page 87 and 88: VFD-F Series• Command code: 08H,
Page 89 and 90: VFD-F Series3.4 CHK (check sum)ASCI
Page 91 and 92: VFD-F Series3.5 Address ListThe con
Page 93 and 94: VFD-F SeriesContent Address Functio
Page 95 and 96: VFD-F Series5.11 Group 10: PID Cont
Page 97 and 98: VFD-F Series This parameter determi
Page 99 and 100:
VFD-F Series In Pr. 11-01 set for 0
Page 101 and 102:
VFD-F Series If multi-function inpu
Page 103 and 104:
VFD-F SeriesFixed amountcirculation
Page 105 and 106:
VFD-F Series11 - 10 Treatment of Fi
Page 107 and 108:
This page intentionally left blankV
Page 109 and 110:
FaultNameVFD-F SeriesFault Descript
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
VFD-F SeriesParameters Functions Se
Page 117 and 118:
VFD-F SeriesGroup 2 Digital Output/
Page 119 and 120:
VFD-F SeriesGroup 3 Output Function
Page 121 and 122:
VFD-F SeriesGroup 4 Input Function
Page 123 and 124:
VFD-F SeriesGroup 5 Multi-step Spee
Page 125 and 126:
VFD-F SeriesGroup 6 Protection Func
Page 127 and 128:
VFD-F SeriesGroup 7 AC Drive and Mo
Page 129 and 130:
VFD-F SeriesGroup 9 Communication P
Page 131 and 132:
VFD-F SeriesGroup 10 PID ControlsPa
Page 133 and 134:
This page intentionally left blankV
Page 135 and 136:
VFD-F SeriesOther FunctionsProtecti
Page 137 and 138:
NOTEVFD-F Series1. Please select th
Page 139 and 140:
VFD-F SeriesB.3 AC Output Reactor R
Page 141 and 142:
VFD-F SeriesB.5 Fuse Specification
Page 143 and 144:
VFD-F SeriesDisplay MessageDescript
Page 145 and 146:
VFD-F SeriesPCB-SUPPORTPCB-SUPPORTS
Page 147 and 148:
VFD-F SeriesVFD015F23A 1.50 kW (2.0
Page 149 and 150:
VFD-F SeriesVFD150F23A 15.0 kW (20.
Page 151 and 152:
VFD-F SeriesVFD300F23A 30.0 kW (40.
Page 153 and 154:
VFD-F SeriesVFD1100F43CVFD1320F43AV
show all

VFD-F (CURVE).cdr

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?