PACKAGING MegaSıva Perlitli is delivered in net 35 kg kraft bags, which are stowed in 42 pcs. on a 80 cm x 120 cm palette (1470 kg). SHELF LIFE The shelf life of the product is 12 months when stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. STORAGE CONDITIONS The product should be stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The container of the product should be closed firmly when not used. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. 111
MegaSıva Elyaflı Cement Based, Manually Applicable Fine Plaster With Fiber Additive PRODUCT DESCRIPTION Cement based pre-final coat surface preparation plaster with enhanced adherence, applied manually, which has been reinforced with various chemical additives in order for enhanced resistance to contraction and shrinkage. AREAS OF USE MegaSıva Elyaflı is applied in indoors and outdoors spaces on prime coated gas concrete and prime coated concrete surface and ceilings and on any roughcast (MegaSıva K, MegaSıva Makine İç, MegaSıva Makine Dıº, MegaSıva Elyaflı K) applied surfaces. PRODUCT ADVANTAGES • Resistant to outdoor conditions. • Ensuring high bonding to the surface, the product does not cause spalling and poses high bonding strength. • Being a high performance product, it does not cause contraction thanks to the fiber additive content. • Prepared and applied easily. PERFORMANCE Dry bulk density 1.45 ± 0.1 gr/cm 3 TS EN 1015 - 10 Compressive strength CS IV TS EN 1015 - 11 Bonding strength > 0.5 N/mm 2 TS EN 1015 - 12 Capillary water absorption coefficient W 1 TS EN 1015 - 18 Water vapor permeability µ < 12 TS EN 1015 - 19 Air content % 7 ± 0.5 TS EN 1015 - 7 > 4 hours (at 20 ± 5°C temperature Workability time and minimum 95 % relative TS EN 1015 - 9 humidity) Reaction to fire A1 TS EN 13501 - 1 The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS EN 998 - 1 (GP) Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.476/D QUALITY CERTIFICATES Conformant to TS EN 998 - 1. CE APPLICATION PROCEDURE Application Surfaces Indoors and Outdoors Walls; - Gas concrete (MegaFilm primer applied) - Concrete (MegaFilm or MegaFilm BB primer applied) - Roughcast applied surfaces Ceilings; - Roughcast applied surfaces Surface Preparation • The application surface should be dry, clean, sound and dust free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir İ or MegaTamir K 24 hours in advance. In the cases, where structural repair mortar should be used; MegaTamir İ Yapısal or MegaTamir K Yapısal should be preferred. • The application surfaces should be moisturized with water, where necessary. • Upon the completion of the surface cleaning, MegaFilm primer should be applied in a single coat with a brush and be left to dry for 1 to 2 hours in order to enhance the bonding strength and stabilize the surface absorption. • Gas concrete surfaces should, prior to the application of the product, be applied MegaFilm primer and the water absorption of the surfaces should so be reduced. • Exposed concrete surfaces should be applied MegaFilm BB exposed concrete primer in single coat and be left to dry for minimum 3 hours prior to the application of the adhesive mortar in order to enhance the adhesion strength. Application Methods • The product should be applied with a steel trowel, whereupon the surface should be smoothed with a floating rule. • The application thickness should ranger between 2 mm and 7 mm. • Once plaster dewaters and is sufficiently hardened following the application, the surface should be processed with a trowel and final finishing touches should be made with a moist sponge. Application Recommendations • The surface should be moisturized intermittently for a period 7 days following the application in order to enhance the endurance of the plaster. • Plaster profiles should be employed on the corners in order to ensure a better quality result and high level of efficiency. • The product should not be applied to such surfaces, to which paint, premixed colorful plaster, base coat plaster or exterior coating, and to gypsum surfaces. • The product should, once mixed, be used before the expiration of its pot life. Any product, the pot life of which has expired, should not be used during the application. • Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared. • Any extra water should not be added to the mixture. • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions, and the product should be mixed with cold water. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and +30°C whilst at application. Application Limits Useful time for prepared mortar - Pot life Plaster surface smoothing time Through dry time The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. APPLICATION INSTRUCTIONS Mixing Ratio The product should be mixed with water, weighing equal to 22 - 24 % of the product. (7.5 - 8.5 liters of water for a 35 kg package) Mixing Equipment • Low speed electrical mixer (400 cycles/min.) • Special tip stirring equipment Mixing Period The product should be stirred with a low-speed mixer until any dry dust and globs are eliminated. The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 3 to 4 minutes following preparation. Application Equipment • Steel trowel • Smoothing trowel Equipment Cleaning The equipment used should be cleaned with water following the application before the mortar dries. TECHNICAL PROPERTIES Chemical Structure: Cement based plaster with fiber additive Dry Density: 1.45 ± 0.1 gr/cm 3 Mortar Density: 1.75 ± 0.1 gr/cm 3 Grain Size: ≤ 600 µm Coat Thickness: 2 - 7 mm Color: Gray, white Maximum 1 hour Minimum 30 minutes Minimum 2 days CONSUMPTION Recommended consumption amounts for application in roughly 1 mm thickness on 1 m 2 surface; 112
- Page 1 and 2:
ADHESIVES MegaFix MegaFix K MegaGra
- Page 3 and 4:
Equipment Cleaning The equipment us
- Page 5 and 6:
Mortar Density: 1.85 ± 0.05 gr/cm
- Page 7 and 8:
CONSUMPTION The consumption amount
- Page 9 and 10:
Application Equipment • Steel not
- Page 11 and 12:
Equipment Cleaning The equipment us
- Page 13 and 14:
Application Equipment • Steel not
- Page 15 and 16:
Grain Size: ≤ 600 µm Color: Gray
- Page 17 and 18:
Equipment Cleaning The equipment us
- Page 19 and 20:
Application Equipment • Steel not
- Page 21 and 22:
Equipment Cleaning The equipment us
- Page 23 and 24:
Temperature Resistance: -15°C to +
- Page 25 and 26:
MegaPro Pastemix Polymer Emulsion B
- Page 27 and 28:
MegaEpoxy Epoxy Resin Based, Double
- Page 29 and 30:
MegaBlok Cement Based, Gas Concrete
- Page 31 and 32:
ARTEFIX Cement Based Ceramic Adhesi
- Page 33 and 34:
BRUFIX Cement Based Ceramic Adhesiv
- Page 35:
JOINT FILLERS MegaFuga MegaFuga Sil
- Page 38 and 39:
Consumption Amount Calculation Meth
- Page 40 and 41:
CONSUMPTION The consumption amount
- Page 42 and 43:
CONSUMPTION The consumption amount
- Page 44 and 45:
Consumption Amount Calculation Meth
- Page 46 and 47:
RECOMMENDED MegaFuga Rustik CONSUMP
- Page 48:
Application Limits Useful time for
- Page 51 and 52:
Megaİzo Lastik Mono Cement Based,
- Page 53 and 54:
Megaİzo Lastik 7 Polymer Emulsion
- Page 55 and 56:
Megaİzo Lastik 10 Polymer Emulsion
- Page 57 and 58:
Megaİzo Lastik 15 Polymer Emulsion
- Page 59 and 60:
Megaİzo Lastik 3 Hydrophobic Impre
- Page 61 and 62:
PACKAGING Megaİzo Lastik 5 is deli
- Page 63 and 64: CONSUMPTION Recommended consumption
- Page 65 and 66: PACKAGING Megaİzo Kristalize is de
- Page 67 and 68: TECHNICAL PROPERTIES Chemical Struc
- Page 69 and 70: Equipment Cleaning The equipment us
- Page 71 and 72: Megaİzo PK3/PK4 - PK3/PK4 Plus - P
- Page 73 and 74: Megaİzo PU 7 Polyurethane Based, R
- Page 75 and 76: Megaİzo PU 10 Polyurethane Based,
- Page 77 and 78: Megaİzo PU 15 Polyurethane Based,
- Page 79 and 80: Megaİzo PU 6 Bitumen Modified, Dou
- Page 81 and 82: Megaİzo PU Mastik LM Polyurethane
- Page 83 and 84: Megaİzo PU Mastik HM Polyurethane
- Page 85 and 86: Megaİzo Stoper Cement Based, Insta
- Page 87 and 88: Megaİzo File Reinforcement And Gla
- Page 90 and 91: REPAIR MORTARS MegaTamir İ MegaTam
- Page 92 and 93: MegaTamir K Cement Based Repair And
- Page 94 and 95: MegaTamir K Yapısal Cement Based S
- Page 96 and 97: MegaTamir Epo Epoxy Based Adhesive
- Page 98 and 99: MegaTamir EpoGrout Epoxy Based, Thr
- Page 101 and 102: FLOORING MATERIALS MegaZemin SL20 M
- Page 103 and 104: MegaZemin BYS Surface Hardening Mor
- Page 106 and 107: PLASTERS MegaSıva İ MegaSıva K M
- Page 108 and 109: PACKAGING MegaSıva İ is delivered
- Page 110 and 111: - Gas concrete surface: 17.5 - 18.5
- Page 112 and 113: PACKAGING MegaSıva Saten is delive
- Page 116 and 117: - Gas concrete surface: 1.5 - 2.5 k
- Page 118 and 119: CONSUMPTION Recommended consumption
- Page 120 and 121: PACKAGING MegaSıva Makine İç is
- Page 122 and 123: PACKAGING MegaSıva Makine Dıº is
- Page 124: MegaSıva Thermo Plaster Mortar For
- Page 127 and 128: MegaFilm Multipurpose Surface Prepa
- Page 129 and 130: MegaFilm Visko Environmental Friend
- Page 131 and 132: MegaFilm İzo Bitumen Emulsion Base
- Page 133 and 134: MegaFilm İzo Epo Epoxy Based, Doub
- Page 136 and 137: ADDITIVES & AUXILIARY MATERIALS Meg
- Page 138 and 139: MegaAntiFreeze 10 Anti-Freeze Morta
- Page 140 and 141: MegaClean Ready To Use Joint And Su
- Page 142 and 143: Mantotherm Adhesive Mortar Adhesive
- Page 144 and 145: Mantotherm Primer Acrylic Emulsion
- Page 146 and 147: Mantotherm Dekominera - Lined Textu
- Page 148 and 149: Mantotherm Exterior Paint With Sili
- Page 150 and 151: Mantotherm Grained Exterior Coating
- Page 152 and 153: Mantotherm EPS Thermal Insulation P
- Page 154 and 155: Mantotherm XPS Thermal Insulation P
- Page 156 and 157: Mantotherm Glass-Fiber Mesh Glass-F
- Page 158 and 159: 151
- Page 161 and 162: k k k k k k k k k
- Page 163 and 164: k k k k k k k k k k k k k k
- Page 165 and 166:
k k k k k k k
- Page 167 and 168:
Areas Of Use
- Page 169 and 170:
Areas Of Use
- Page 171 and 172:
Areas Of Use
- Page 173:
Areas Of Use