construction chemicals

More documents

Recommendations

Info

Mantotherm XPS Thermal Insulation Panel Compressed Polystyrene Board With High Pressure Resistance PRODUCT DESCRIPTION Compressed close-pore polystyrene board with high pressure resistance, used for the heat insulation of walls, columns and girders. AREAS OF USE Mantotherm XPS Thermal Insulation Panel is used as heat insulation material for the internal and external walls, terraces, floors and basements of buildings. PRODUCT ADVANTAGES • Closed pore. • Highly resistant to pressure. • Preserves the buildings from the outer atmospheric impacts, prevents corrosion and elongates the service life of buildings. • Capable of successfully bearing the short- and long-term mechanical charges, which may occur in a building under normal conditions. • Resistant to impacts. • Has an infinite economic life. The insulating nature of the product does not change in time. • Poses low thermal conductivity. • Does not lose its thickness and endures through the time. • Very lightweight, easy to carry. • Easy to application. • Environmentally friendly. PERFORMANCE Length tolerance >1000 ; ± 10 mm TS EN 1602 Width tolerance
Mantotherm Rockwool Thermal Insulation Panel . Thermal, Noise And Fire Insulation Material With Natural Fiber Content PRODUCT DESCRIPTION The thermal, noise and fire insulation material, which is developed through the transformation of volcanic rocks by melting at high temperatures. AREAS OF USE Mantotherm Rockwool Thermal Insulation Panel is used as heat insulation material for the internal and external walls, terraces, floors and basements of buildings. PRODUCT ADVANTAGES • Resistance to temperatures above 1000°C at structures provide full fire safety. • Absorbing noise and vibration, the product creates a peaceful and healthy living space. • Water repellent. • Has a high water vapor permeability. • Free from effects caused by temperature changes thanks to its dimensional stability. • Thanks to its long fiber structure, the product enables the obtainment of products with plat edges and a smooth surface for the purpose of cutting and lamination applications. • Does not release any harmful gases. • Does not corrode, perish and mold. • Does not cause corrosion and oxidization. • Poses low thermal conductivity. PERFORMANCE Length tolerance 1200 ± %2 Width tolerance 600 ± %1.5 TS EN 822 Thickness tolerance T5 TS EN 823 Deviation from squareness Maximum 5 mm/m TS EN 824 Surface smoothness Maximum 6 mm/m TS EN 825 Density 150 ± %10 kg/m 3 TS EN 1602 λ (Thermal Conductivity Coefficient) 0.040 W/mK TS EN 12667 TS EN 12939 Short term water absorption WS TS EN 1609 Long term water absorption WL(P) TS EN 12087 Compressive strength 50 kPa TS EN 826 Dimensional stability under certain temperature conditions DS(T+) TS EN 1604 Water vapor permeability 1 µ TS EN 12086 Reaction to fire A1 TS EN 13501-1 The foregoing values represent the results of the laboratory tests. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS EN 13162 ETAG 004 QUALITY CERTIFICATES TSE CE Conformant to ETAG 004. APPLICATION PROCEDURE Application Surfaces Outdoors Walls; - Roughcast applied surfaces Indoors Walls; - Finishing coat applied surfaces Terraces and Roofs Surface Preparation • The application surface should be dry, clean, sound and dust-free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The old plaster coat, blistering and cracks on the facades should be scraped, be repaired with MegaTamir İ or MegaTamir K, whereby a sound surface should be obtained. • In the case of bevels in excess of 2 cm on the surface; they should be repaired with MegaTamir İ or MegaTamir K before insulation application. • The surface to be insulated should not be moist, and the flooring trowel coating and internal and external wall plasters should have dried. • There should not be any moisture in progress upward on the surface, the waterproofing should be completed as necessary and should have risen 30 cm above the ground soil. • The insulation application should be initiated minimum 4 weeks after the application of roughcast. • The rain gutters, cabling elements and the like on the façade should be placed over the system and be deployed in some 6 to 7 cm distance to the system. wall and to ensure the smoothness of the surface, the board should be slipped slightly and adhered to the wall, be gauged and linaged. • Mantotherm Rockwool Thermal Insulation Panel should be furnished in tusk tenon fashion. The tusk tenon should be continued also in the corner joint spots of the building. • Any unintentional gaps between any two Mantotherm Rockwool Thermal Insulation Panel should strictly be filled with pieces to be cut from the same material. Due care must be taken to ensure that the adhesive does not overflow at the edges, where boards join, any overflowing adhesive should be cleaned and the board edges should be ensured to be clean. • The corners of the such gaps on the surface as window gaps and door gaps should be aligned with the board joints, the thermal insulating boards should be placed as a whole on the corners, screw threads should be cut and be sized for the gaps. Hence will be eliminated the risk of cracks on the corners. • Mechanical fixation on the surface of the thermal insulating boards in addition to chemical adhesion is of utmost importance for long-lasting performance. Minimum 24 hours after the adhesion of the thermal insulating boards, the dowelling should be performed with Mantotherm Thermal Insulation Panel Dowels. Appropriate and suitable dowels should be selected with due consideration of the insulating material employed and the surface characteristics. Application Recommendations • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be given to prevent the exposure of the material to direct sunlight in hot weather conditions. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and +30°C whilst at application. APPLICATION INSTRUCTIONS Application Equipment - Steel notched trowel (for Rockwool adhered by dredging) - Steel trowel Equipment Cleaning The equipment used should be cleaned with water following the application before the mortar dries. TECHNICAL PROPERTIES Chemical Structure: Thermal insulation board with natural fiber content Color: Characteristic (green - black) CONSUMPTION Recommended consumption amount for application on 1 m 2 surface is 1.0 m 2 . The said value may vary, depending on the surface and ambient conditions. PACKAGING (Panel Dimensions: 60 cm x120 cm) Number of Panels per 1 Package Mantotherm Rockwool 3 cm 8 Mantotherm Rockwool 4 cm 6 Mantotherm Rockwool 5 cm 5 Mantotherm Rockwool 6 cm 4 Mantotherm Rockwool 8 cm 3 Mantotherm Rockwool 10 cm 2 STORAGE CONDITIONS The product should be stored within non-tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The product should be preserved from water, physical damage and flame sources. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. Application Methods • Mantotherm Rockwool Thermal Insulation Panel, the reserve side of should have been applied Mantotherm Adhesive Mortar, should be firmly placed on the sub-basement profile. • In order for Mantotherm Rockwool Thermal Insulation Panel to thoroughly contact the 148
Page 1 and 2:
ADHESIVES MegaFix MegaFix K MegaGra
Page 3 and 4:
Equipment Cleaning The equipment us
Page 5 and 6:
Mortar Density: 1.85 ± 0.05 gr/cm
Page 7 and 8:
CONSUMPTION The consumption amount
Page 9 and 10:
Application Equipment • Steel not
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Grain Size: ≤ 600 µm Color: Gray
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Temperature Resistance: -15°C to +
Page 25 and 26:
MegaPro Pastemix Polymer Emulsion B
Page 27 and 28:
MegaEpoxy Epoxy Resin Based, Double
Page 29 and 30:
MegaBlok Cement Based, Gas Concrete
Page 31 and 32:
ARTEFIX Cement Based Ceramic Adhesi
Page 33 and 34:
BRUFIX Cement Based Ceramic Adhesiv
Page 35:
JOINT FILLERS MegaFuga MegaFuga Sil
Page 38 and 39:
Consumption Amount Calculation Meth
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Consumption Amount Calculation Meth
Page 46 and 47:
RECOMMENDED MegaFuga Rustik CONSUMP
Page 48:
Application Limits Useful time for
Page 51 and 52:
Megaİzo Lastik Mono Cement Based,
Page 53 and 54:
Megaİzo Lastik 7 Polymer Emulsion
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Megaİzo Lastik 3 Hydrophobic Impre
Page 61 and 62:
PACKAGING Megaİzo Lastik 5 is deli
Page 63 and 64:
CONSUMPTION Recommended consumption
Page 65 and 66:
PACKAGING Megaİzo Kristalize is de
Page 67 and 68:
TECHNICAL PROPERTIES Chemical Struc
Page 69 and 70:
Page 71 and 72:
Megaİzo PK3/PK4 - PK3/PK4 Plus - P
Page 73 and 74:
Megaİzo PU 7 Polyurethane Based, R
Page 75 and 76:
Megaİzo PU 10 Polyurethane Based,
Page 77 and 78:
Megaİzo PU 15 Polyurethane Based,
Page 79 and 80:
Megaİzo PU 6 Bitumen Modified, Dou
Page 81 and 82:
Megaİzo PU Mastik LM Polyurethane
Page 83 and 84:
Megaİzo PU Mastik HM Polyurethane
Page 85 and 86:
Megaİzo Stoper Cement Based, Insta
Page 87 and 88:
Megaİzo File Reinforcement And Gla
Page 90 and 91:
REPAIR MORTARS MegaTamir İ MegaTam
Page 92 and 93:
MegaTamir K Cement Based Repair And
Page 94 and 95:
MegaTamir K Yapısal Cement Based S
Page 96 and 97:
MegaTamir Epo Epoxy Based Adhesive
Page 98 and 99:
MegaTamir EpoGrout Epoxy Based, Thr
Page 101 and 102:
FLOORING MATERIALS MegaZemin SL20 M
Page 103 and 104: MegaZemin BYS Surface Hardening Mor
Page 106 and 107: PLASTERS MegaSıva İ MegaSıva K M
Page 108 and 109: PACKAGING MegaSıva İ is delivered
Page 110 and 111: - Gas concrete surface: 17.5 - 18.5
Page 112 and 113: PACKAGING MegaSıva Saten is delive
Page 114 and 115: PACKAGING MegaSıva Perlitli is del
Page 116 and 117: - Gas concrete surface: 1.5 - 2.5 k
Page 118 and 119: CONSUMPTION Recommended consumption
Page 120 and 121: PACKAGING MegaSıva Makine İç is
Page 122 and 123: PACKAGING MegaSıva Makine Dıº is
Page 124: MegaSıva Thermo Plaster Mortar For
Page 127 and 128: MegaFilm Multipurpose Surface Prepa
Page 129 and 130: MegaFilm Visko Environmental Friend
Page 131 and 132: MegaFilm İzo Bitumen Emulsion Base
Page 133 and 134: MegaFilm İzo Epo Epoxy Based, Doub
Page 136 and 137: ADDITIVES & AUXILIARY MATERIALS Meg
Page 138 and 139: MegaAntiFreeze 10 Anti-Freeze Morta
Page 140 and 141: MegaClean Ready To Use Joint And Su
Page 142 and 143: Mantotherm Adhesive Mortar Adhesive
Page 144 and 145: Mantotherm Primer Acrylic Emulsion
Page 146 and 147: Mantotherm Dekominera - Lined Textu
Page 148 and 149: Mantotherm Exterior Paint With Sili
Page 150 and 151: Mantotherm Grained Exterior Coating
Page 152 and 153: Mantotherm EPS Thermal Insulation P
Page 156 and 157: Mantotherm Glass-Fiber Mesh Glass-F
Page 158 and 159: 151
Page 161 and 162: k k k k k k k k k
Page 163 and 164: k k k k k k k k k k k k k k
Page 165 and 166: k k k k k k k
Page 167 and 168: Areas Of Use
Page 173: Areas Of Use
show all

construction chemicals

Create successful ePaper yourself

Delete template?

Save as template?