construction chemicals

More documents

Recommendations

Info

MegaPro Facade Cement And Polymer Emulsion Based, Double Compound, High Performance, Highly Elastic, Large Size Ceramic Adhesive Mortar PRODUCT DESCRIPTION Cement and polymer emulsion based, double component elastic adhesive with reduced slippage, high adherence and elongated workable time for large size coating applications such as ceramic, granite ceramic, marble, natural rock and porcelain, which is resistant to temperature changes, water and frost. AREAS OF USE MegaPro Facade is used for the adhesion on such sound, dust free vertical and horizontal cement based plaster, trowel coating and prime coated concrete surfaces and coating materials with low water absorbance as ceramic tiles in indoors and outdoors spaces. The product, absorbing temperature changes, vibrated surface movements, deformations such as expansion and shrinkage thanks to its high elasticity especially in such environments and on such surfaces that require high elasticity and strength, enables secure adhesion. The product is suitable for use in such spaces characterized by sudden changes in temperature such as cold storage rooms, quick freezing facilities, exteriors of furnaces and floor heated systems. The product is also used on the floors and the walls of such spaces characterized by vibration as metro stations, terminals and coach stations. The product is also used for ceramic tile adhesion applications on old ceramic tile coated surfaces. PRODUCT ADVANTAGES • Ideal for the adhesion of large size and thick coating materials. • Displays high performance in applications with all coating materials and on all types of surfaces. • Poses high elasticity and bonding strength thanks to the polymer additive. • Water and frost resistant. • Poses a longer workable time thanks to the elongated retention time thereof. • Prepared and applied easily. • Does not cause slippage in the case of vertical applications. PERFORMANCE Initial tensile adhesion strength ≥ 1N/mm 2 TS EN 1348 Tensile adhesion strength after water immersion ≥ 1 N/mm 2 TS EN 1348 Tensile adhesion strength after thermal aging ≥ 1 N/mm 2 TS EN 1348 Tensile adhesion strength after freezing - thawing cycle ≥ 1 N/mm 2 TS EN 1348 Tensile adhesion strength after retention time (after 30 minutes) ≥ 0.5 N/mm 2 TS EN 1346 Transverse deformation S2 ≥ 5 mm TS EN 12002 Reaction to fire A1 TS EN 13501 - 1 The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. REFERENCE STANDARDS Certifications/Standards TS EN 12004 /C2TES2 Ministry of Public Works and Settlement Item No. Ministry of Public Works and Settlement Item No.: 04.013/1 Ministry of Public Works and Settlement Item No.: 04.013/4 QUALITY CERTIFICATES Conformant to TS EN 12004. APPLICATION PROCEDURE Application Surfaces Indoors and Outdoors Walls; - Cement based plaster (MegaFilm primer applied) - Concrete (MegaFilm or MegaFilm BB primer applied) - Old ceramic tile coating (MegaFilm Visko primer applied) Indoors and Outdoors Floors; - Cement based trowel coating (MegaFilm primer applied) - Concrete (MegaFilm or MegaFilm BB primer applied) - Old ceramic tile coating (MegaFilm Visko primer applied) Surface Preparation • The application surface should be dry, clean, sound and dust free, and should have been cleansed of oil, dirt or any materials that may prevent adhesion, and any such materials as mortar and cement residues should be scraped from the application surface. • The dusty surface on the reverse side of the ceramic tile should be moisturized and cleaned. • The surface defects, which are deeper than 1 cm, should be repaired with MegaTamir İ or MegaTamir K 24 hours in advance of the adhesive mortar application. In the cases, where structural repair mortar should be used; MegaTamir İ Yapısal or MegaTamir K Yapısal should be preferred. • Upon the completion of the surface cleaning, MegaFilm primer should be applied in a single coat with a brush and be left to dry for 1 to 2 hours in order to enhance the bonding strength and stabilize the surface absorption. • Exposed concrete surfaces should be applied MegaFilm BB exposed concrete primer in single coat and be left to dry for minimum 3 hours prior to the application of the adhesivemortar in order to enhance the adhesion strength. • In the case of ceramic tile coating application on old ceramic tile coating, the surface should, prior to the application, be prepared by applying MegaFilm Visko and to dry for minimum 3 hours. • In the case of wet space applications, waterproofing should be ensured with Megaİzo Lastik 10 on the surface, which should have been coated with the recommended primer, prior to ceramic flooring. Application Methods • MegaPro Facade should be applied to the surface with the notched trowel determined with respect to the size of the ceramic tile and the structural condition of the surface. • Due care must be taken to ensure that MegaPro Facade does not form a film layer on the surface during the application. In the cases of formation of film layer on the surface, the adhesive should be scraped off the surface and should never be used again. • The coating material should be placed on the surface and be ensured to settle thereon with a rubber tip hammer. • Joint filling should be initiated minimum 24 hours after the adhesion. • In the case of the applications with ceramic tiles with dimensions in excess of 33x33 cm in indoors and outdoors spaces; double-side adhesion should be applied. • Minimum 3 mm joint gaps should be allowed amongst large size coating materials. • In the case of exterior and vertical surface applications, the product enables coating materials up to 60x60 cm in size to be safely adhered at such heights up to 10 meters. • Minimum 10 mm long expansion joint gap should be allowed for each 30 m 2 surface area, which gaps should be filled with Megaİzo PU Mastik HM. Application Recommendations • The product should, once mixed, be used before the expiration of its pot life. Any mortar, the pot life of which has expired, should not be used during the application. • Any such foreign substance as lime, cement or plaster should not be added to the mortar prepared. • Any extra water should not be added to the mixture. • The product should not be applied on unsound surfaces. The soundness and the load bearing capacity of old surfaces should be checked prior to adhesion. • The surface should be preserved from air currents and water contact during and after the application. • The product should not be applied to such surfaces, which are exposed to risk of freezing within the next 24 hours, which are frozen or the frost of which is thawing. • Due care should be taken to ensure that the material is not exposed to direct sunlight in hot weather conditions. • The product should not be applied on extremely windy weather conditions or on hot surfaces, which are exposed to direct sunlight; and in the cases, where application is imperative under such conditions, the environment and the surface should be prepared for application in advance. • The product should not be applied in rainy weather conditions, and the application surface should be preserved from rain for a period of 24 hours. • Refer to our technical support hotline for recommendation on different surface applications. (PHONE: 444 4 595) Surface and Ambient Temperature The surface and ambient temperature should be between +5°C and +35°C whilst at application. Application Limits Useful time for prepared mortar - Pot life Workable time Smoothing time Required standby time for joint application Opening the traffic The foregoing values represent the results of the laboratory tests conducted at 23 ± 2°C temperature and 50% ± 5 relative humidity conditions. The values provided as per the table may vary depending on the surface and ambient conditions. APPLICATION INSTRUCTIONS Mixing Ratio 25 kg powder component should be mixed with the 6 kg liquid component. Mixing Equipment • Low speed electrical mixer (400 cycles/min.) • Special tip stirring equipment Maximum 2 hours Maximum 50 minutes 30 minutes 24 hours 24 - 48 hours Mixing Period The product should be stirred with a low speed mixer until any dry dust and globs are eliminated. The mortar should, then, be stirred once again for 1 to 2 minutes after being had settled for 5 to 10 minutes following preparation. 25
Application Equipment • Steel notched trowel determined with respect to the size of ceramic tile and the structure of the surface • Rubber tip ceramic hammer Equipment Cleaning The equipment used should be cleaned with water following the application before the mortar dries. TECHNICAL PROPERTIES Chemical Structure: Cement based ceramic tile adhesive mortar with polymer additive Dry Density: 1.35 ± 0.05 gr/cm 3 Mortar Density: 1.75± 0.05 gr/cm 3 Grain Size: ≤ 600 µm Color: Gray Temperature Resistance: -15°C to +80°C CONSUMPTION The consumption amount varies depending on the condition of the application surface and the coating material. Ceramic Tile Size Notch Size Consumption 10x10 cm to 10x15 cm or Single side adhesion: 4.0 - 4.5 kg/m 2 6x6x6 smaller Double side adhesion: 6.0 - 6.5 kg/m 2 10x15 to 25x40 cm Single side adhesion: 4.5 - 5.0 kg/m 2 8x8x8 10x15 to 33x33 cm Double side adhesion: 7.0 - 7.5 kg/m 2 Single side adhesion: 5.5 - 6.0 kg/m 2 25x40 to 33x33 cm or larger 10x10x10 Double side adhesion: 7.5 - 8.0 kg/m 2 PACKAGING MegaPro Facade is delivered as a set of powder component in net 25 kg kraft bags and liquid component in net 6 kg plastic drum. SHELF LIFE The shelf life of the product is 12 months when stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. STORAGE CONDITIONS The product should be stored within non tampered original packaging in dry (maximum relative humidity 60 %) and cool (ambient temperature between +5°C and +25°C) environment. It should not be exposed to direct sunlight. The container of the product should be closed firmly when not used. SAFETY PRECAUTIONS Please refer to the Safety Data Sheet (SDS) as appropriate for easy and safe application. 26
Page 1 and 2: ADHESIVES MegaFix MegaFix K MegaGra
Page 3 and 4: Equipment Cleaning The equipment us
Page 5 and 6: Mortar Density: 1.85 ± 0.05 gr/cm
Page 7 and 8: CONSUMPTION The consumption amount
Page 9 and 10: Application Equipment • Steel not
Page 13 and 14: Application Equipment • Steel not
Page 15 and 16: Grain Size: ≤ 600 µm Color: Gray
Page 17: Equipment Cleaning The equipment us
Page 23 and 24: Temperature Resistance: -15°C to +
Page 25 and 26: MegaPro Pastemix Polymer Emulsion B
Page 27 and 28: MegaEpoxy Epoxy Resin Based, Double
Page 29 and 30: MegaBlok Cement Based, Gas Concrete
Page 31 and 32: ARTEFIX Cement Based Ceramic Adhesi
Page 33 and 34: BRUFIX Cement Based Ceramic Adhesiv
Page 35: JOINT FILLERS MegaFuga MegaFuga Sil
Page 38 and 39: Consumption Amount Calculation Meth
Page 44 and 45: Consumption Amount Calculation Meth
Page 46 and 47: RECOMMENDED MegaFuga Rustik CONSUMP
Page 48: Application Limits Useful time for
Page 51 and 52: Megaİzo Lastik Mono Cement Based,
Page 53 and 54: Megaİzo Lastik 7 Polymer Emulsion
Page 59 and 60: Megaİzo Lastik 3 Hydrophobic Impre
Page 61 and 62: PACKAGING Megaİzo Lastik 5 is deli
Page 63 and 64: CONSUMPTION Recommended consumption
Page 65 and 66: PACKAGING Megaİzo Kristalize is de
Page 67 and 68: TECHNICAL PROPERTIES Chemical Struc
Page 69 and 70:
Equipment Cleaning The equipment us
Page 71 and 72:
Megaİzo PK3/PK4 - PK3/PK4 Plus - P
Page 73 and 74:
Megaİzo PU 7 Polyurethane Based, R
Page 75 and 76:
Megaİzo PU 10 Polyurethane Based,
Page 77 and 78:
Megaİzo PU 15 Polyurethane Based,
Page 79 and 80:
Megaİzo PU 6 Bitumen Modified, Dou
Page 81 and 82:
Megaİzo PU Mastik LM Polyurethane
Page 83 and 84:
Megaİzo PU Mastik HM Polyurethane
Page 85 and 86:
Megaİzo Stoper Cement Based, Insta
Page 87 and 88:
Megaİzo File Reinforcement And Gla
Page 90 and 91:
REPAIR MORTARS MegaTamir İ MegaTam
Page 92 and 93:
MegaTamir K Cement Based Repair And
Page 94 and 95:
MegaTamir K Yapısal Cement Based S
Page 96 and 97:
MegaTamir Epo Epoxy Based Adhesive
Page 98 and 99:
MegaTamir EpoGrout Epoxy Based, Thr
Page 101 and 102:
FLOORING MATERIALS MegaZemin SL20 M
Page 103 and 104:
MegaZemin BYS Surface Hardening Mor
Page 106 and 107:
PLASTERS MegaSıva İ MegaSıva K M
Page 108 and 109:
PACKAGING MegaSıva İ is delivered
Page 110 and 111:
- Gas concrete surface: 17.5 - 18.5
Page 112 and 113:
PACKAGING MegaSıva Saten is delive
Page 114 and 115:
PACKAGING MegaSıva Perlitli is del
Page 116 and 117:
- Gas concrete surface: 1.5 - 2.5 k
Page 118 and 119:
CONSUMPTION Recommended consumption
Page 120 and 121:
PACKAGING MegaSıva Makine İç is
Page 122 and 123:
PACKAGING MegaSıva Makine Dıº is
Page 124:
MegaSıva Thermo Plaster Mortar For
Page 127 and 128:
MegaFilm Multipurpose Surface Prepa
Page 129 and 130:
MegaFilm Visko Environmental Friend
Page 131 and 132:
MegaFilm İzo Bitumen Emulsion Base
Page 133 and 134:
MegaFilm İzo Epo Epoxy Based, Doub
Page 136 and 137:
ADDITIVES & AUXILIARY MATERIALS Meg
Page 138 and 139:
MegaAntiFreeze 10 Anti-Freeze Morta
Page 140 and 141:
MegaClean Ready To Use Joint And Su
Page 142 and 143:
Mantotherm Adhesive Mortar Adhesive
Page 144 and 145:
Mantotherm Primer Acrylic Emulsion
Page 146 and 147:
Mantotherm Dekominera - Lined Textu
Page 148 and 149:
Mantotherm Exterior Paint With Sili
Page 150 and 151:
Mantotherm Grained Exterior Coating
Page 152 and 153:
Mantotherm EPS Thermal Insulation P
Page 154 and 155:
Mantotherm XPS Thermal Insulation P
Page 156 and 157:
Mantotherm Glass-Fiber Mesh Glass-F
Page 158 and 159:
151
Page 161 and 162:
k k k k k k k k k
Page 163 and 164:
k k k k k k k k k k k k k k
Page 165 and 166:
k k k k k k k
Page 167 and 168:
Areas Of Use
Page 169 and 170:
Areas Of Use
Page 171 and 172:
Areas Of Use
Page 173:
Areas Of Use
show all

construction chemicals

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?