PROFINET Installation Guideline for Cabling and Assembly

More documents

Recommendations

Info

• As soon as the cable is subject to mechanical stress caused by movement or during installation or when using it in drag chains, the temperature range is reduced significantly. Observe the manufacturers instructions. 1.3.4 Tensile strength Laying PROFINET cables The manufacturer specifies a maximum tensile strength for each cable type. The PROFINET cable can be damaged or even destroyed when this maximum tensile strength is exceeded. This is important because of the high mechanical stress when using drag chains or festoon attachment, or because of the tensile force generated when laying the cable. Please select from the table below the cable type best suited for each application: PROFINET cable Suited for Non-flexible (solid core) Stationary use without any motion Flexible Occasional motion or vibrations Permanent movement Special applications, e.g. permanent motion, vibrations or highly flexible Table 4: Electrical PROFINET cable types © Copyright by PNO 2009 – all rights reserved 31/99
• Carefully unreel the PROFINET cable from the drum by hand, only. • Do not apply force to pull it off. Laying PROFINET cables 1.3.5 Using pulling aid and protecting connectors • Use cable stockings when pulling in PROFINET cables. If the PROFINET cable has already been pre-assembled, protect the connector by using a plastic or metal tube to cover the connector. 32/99 © Copyright by PNO 2009 – all rights reserved No
Page 1 and 2: PROFINET Installation Guideline for
Page 3 and 4: PROFINET Order No: 8.072 Identifica
Page 5 and 6: Table of contents 1. Laying PROFINE
Page 7 and 8: List of figures Figure 1: Cable dis
Page 9 and 10: Safety instructions The use of the
Page 11 and 12: Liability exclusion The PROFIBUS Us
Page 13 and 14: Symbols This document contains vari
Page 15 and 16: This page is intentionally left bla
Page 17 and 18: Laying PROFINET cables 1.1 Routing
Page 19 and 20: How to read the table Laying PROFIN
Page 21 and 22: • Metallic conductive cable ducts
Page 23 and 24: If the cables are laid in metallic
Page 25 and 26: Laying PROFINET cables Only use app
Page 27 and 28: This page is intentionally left bla
Page 29 and 30: • In areas where people can step
Page 31: • Store and transport the cable r
Page 35 and 36: 1.3.8 Distortion • Distortion, an
Page 37 and 38: Laying PROFINET cables 1.3.11 Keepi
Page 39 and 40: Laying PROFINET cables 1.3.13 Avoid
Page 41 and 42: Laying PROFINET cables 1.5.1 Laying
Page 43 and 44: • If copper PROFINET cables are l
Page 45 and 46: PROFINET cable assembly work 2.1 PR
Page 47 and 48: PROFINET cable assembly work Note t
Page 49 and 50: Manuf. instructions PROFINET cable
Page 51 and 52: • Push down the retainer. • Clo
Page 53 and 54: • Open the connector. • Slide t
Page 55 and 56: PROFINET cable assembly work 2.1.5
Page 57 and 58: • Push the two parts of the conne
Page 59 and 60: Manuf. instructions PROFINET cable
Page 63 and 64: PROFINET cable assembly work The ne
Page 65 and 66: PROFINET cable assembly work For mu
Page 67 and 68: • Strip the FO cable sheath. •
Page 69 and 70: Guideline for further details • P
Page 71 and 72: • Strip the external jacket and t
Page 73 and 74: Optical measurement PROFINET cable
Page 75 and 76: PROFINET cable assembly work As pro
Page 77 and 78: • Interconnect all shields and gr
Page 79 and 80: • Connect the metal cable trays t
Page 83 and 84:
• Do not use the shield connectio
Page 85 and 86:
This page is intenionally left blan
Page 87 and 88:
Connecting PROFINET nodes 3.1.1 Ele
Page 89 and 90:
• Due to its design, it is normal
Page 91 and 92:
This page is intentionally left bla
Page 93 and 94:
Glossary Terms and definitions Comm
Page 95 and 96:
Terms and definitions Optical trans
Page 97 and 98:
Alphabetic index 96/99 © Copyright
Page 99 and 100:
98/99 © Copyright by PNO 2009 - al
Page 101:
Order No.: 8.072 01/2009 © Copyrig
show all

PROFINET Installation Guideline for Cabling and Assembly

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?