PROFINET Installation Guideline for Cabling and Assembly

More documents

Recommendations

Info

PROFINET cable assembly work PROFINET Insulation displacement technology usually consists of a compatible system of connectors, cable and stripping tool. You shall only use components that are part of the manufacturer's system in order to avoid problems. This type of connector is available from different manufacturers in various styles. The next section shows as an example the principal steps to assemble such a kind of connector. The exact Dprocedure might differ from vendor to vendor. Please observe the manufacturer's instuctions. • Open the connector • Strip off the cable by using a stripp off tool. This tool is sold suiting to the diameter of the cable. Make sure that you adhere to the given lengths for the shield and the wires. When using the genuine stripping tool for PROFINET cable, this is automatically the case. • Insert the wires into the tansparent retainer. Match the color of the wire to the color code of the retainer © Copyright by PNO 2009 – all rights reserved 49/99
• Push down the retainer. • Close the housing. Ensure proper contact between the cable shield and the connector housing. • Lock the housing PROFINET cable assembly work For insulation displacement technology there are appropriate stripping tools for each manufacturer's system. These tools not only strip the insulation, but also prepare the cable shield ready for good connection. They considerably facilitate the assembly of connectors and reduce the assembly time. 50/99 © Copyright by PNO 2009 – all rights reserved
Page 1 and 2: PROFINET Installation Guideline for
Page 3 and 4: PROFINET Order No: 8.072 Identifica
Page 5 and 6: Table of contents 1. Laying PROFINE
Page 7 and 8: List of figures Figure 1: Cable dis
Page 9 and 10: Safety instructions The use of the
Page 11 and 12: Liability exclusion The PROFIBUS Us
Page 13 and 14: Symbols This document contains vari
Page 15 and 16: This page is intentionally left bla
Page 17 and 18: Laying PROFINET cables 1.1 Routing
Page 19 and 20: How to read the table Laying PROFIN
Page 21 and 22: • Metallic conductive cable ducts
Page 23 and 24: If the cables are laid in metallic
Page 25 and 26: Laying PROFINET cables Only use app
Page 29 and 30: • In areas where people can step
Page 31 and 32: • Store and transport the cable r
Page 33 and 34: • Carefully unreel the PROFINET c
Page 35 and 36: 1.3.8 Distortion • Distortion, an
Page 37 and 38: Laying PROFINET cables 1.3.11 Keepi
Page 39 and 40: Laying PROFINET cables 1.3.13 Avoid
Page 41 and 42: Laying PROFINET cables 1.5.1 Laying
Page 43 and 44: • If copper PROFINET cables are l
Page 45 and 46: PROFINET cable assembly work 2.1 PR
Page 47 and 48: PROFINET cable assembly work Note t
Page 49: Manuf. instructions PROFINET cable
Page 53 and 54: • Open the connector. • Slide t
Page 55 and 56: PROFINET cable assembly work 2.1.5
Page 57 and 58: • Push the two parts of the conne
Page 59 and 60: Manuf. instructions PROFINET cable
Page 63 and 64: PROFINET cable assembly work The ne
Page 65 and 66: PROFINET cable assembly work For mu
Page 67 and 68: • Strip the FO cable sheath. •
Page 69 and 70: Guideline for further details • P
Page 71 and 72: • Strip the external jacket and t
Page 73 and 74: Optical measurement PROFINET cable
Page 75 and 76: PROFINET cable assembly work As pro
Page 77 and 78: • Interconnect all shields and gr
Page 79 and 80: • Connect the metal cable trays t
Page 83 and 84: • Do not use the shield connectio
Page 85 and 86: This page is intenionally left blan
Page 87 and 88: Connecting PROFINET nodes 3.1.1 Ele
Page 89 and 90: • Due to its design, it is normal
Page 93 and 94: Glossary Terms and definitions Comm
Page 95 and 96: Terms and definitions Optical trans
Page 97 and 98: Alphabetic index 96/99 © Copyright
Page 99 and 100: 98/99 © Copyright by PNO 2009 - al
Page 101:
Order No.: 8.072 01/2009 © Copyrig
show all

PROFINET Installation Guideline for Cabling and Assembly

Create successful ePaper yourself

Delete template?

Save as template?