PROFINET Installation Guideline for Cabling and Assembly

More documents

Recommendations

Info

• Tighten the contact clamps using a screw driver (observe torque). • Connect the shield. For this, you usually fold back the cable braid over a metal sleeve. Insert a gasket into the sleeve in order to seal the connector. Make sure that the shield wires to not touch the gasked. Ensure there is no shortcircuit between the shield and the data wires. • Close and tighten the connector, making sure that the wires inside the connector are not twisted as the screwed housing is assembled PROFINET cable assembly work © Copyright by PNO 2009 – all rights reserved Observe torque! 53/99
PROFINET cable assembly work 2.1.5 M12 insulation displacement technology Manuf. instructions Manufacturer instructions: Read the connector manufacturer’s instructions. These instructions provide valuable information on the connector design. The following description reflects the basic procedure, but by no means does it replace the manufacturer's instructions. The main advantage of insulation displacement technology is quicker and simpler assembly procedure. The general steps are: • Open the connector. 54/99 © Copyright by PNO 2009 – all rights reserved
Page 1 and 2:
PROFINET Installation Guideline for
Page 3 and 4: PROFINET Order No: 8.072 Identifica
Page 5 and 6: Table of contents 1. Laying PROFINE
Page 7 and 8: List of figures Figure 1: Cable dis
Page 9 and 10: Safety instructions The use of the
Page 11 and 12: Liability exclusion The PROFIBUS Us
Page 13 and 14: Symbols This document contains vari
Page 15 and 16: This page is intentionally left bla
Page 17 and 18: Laying PROFINET cables 1.1 Routing
Page 19 and 20: How to read the table Laying PROFIN
Page 21 and 22: • Metallic conductive cable ducts
Page 23 and 24: If the cables are laid in metallic
Page 25 and 26: Laying PROFINET cables Only use app
Page 29 and 30: • In areas where people can step
Page 31 and 32: • Store and transport the cable r
Page 33 and 34: • Carefully unreel the PROFINET c
Page 35 and 36: 1.3.8 Distortion • Distortion, an
Page 37 and 38: Laying PROFINET cables 1.3.11 Keepi
Page 39 and 40: Laying PROFINET cables 1.3.13 Avoid
Page 41 and 42: Laying PROFINET cables 1.5.1 Laying
Page 43 and 44: • If copper PROFINET cables are l
Page 45 and 46: PROFINET cable assembly work 2.1 PR
Page 47 and 48: PROFINET cable assembly work Note t
Page 49 and 50: Manuf. instructions PROFINET cable
Page 51 and 52: • Push down the retainer. • Clo
Page 53: • Open the connector. • Slide t
Page 57 and 58: • Push the two parts of the conne
Page 59 and 60: Manuf. instructions PROFINET cable
Page 61 and 62: PROFINET cable assembly work 2.2.3
Page 63 and 64: PROFINET cable assembly work The ne
Page 65 and 66: PROFINET cable assembly work For mu
Page 67 and 68: • Strip the FO cable sheath. •
Page 69 and 70: Guideline for further details • P
Page 71 and 72: • Strip the external jacket and t
Page 73 and 74: Optical measurement PROFINET cable
Page 75 and 76: PROFINET cable assembly work As pro
Page 77 and 78: • Interconnect all shields and gr
Page 79 and 80: • Connect the metal cable trays t
Page 81 and 82: PROFINET cable assembly work 2.3.7
Page 83 and 84: • Do not use the shield connectio
Page 85 and 86: This page is intenionally left blan
Page 87 and 88: Connecting PROFINET nodes 3.1.1 Ele
Page 89 and 90: • Due to its design, it is normal
Page 93 and 94: Glossary Terms and definitions Comm
Page 95 and 96: Terms and definitions Optical trans
Page 97 and 98: Alphabetic index 96/99 © Copyright
Page 99 and 100: 98/99 © Copyright by PNO 2009 - al
Page 101: Order No.: 8.072 01/2009 © Copyrig
show all

PROFINET Installation Guideline for Cabling and Assembly

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?