PROFINET Installation Guideline for Cabling and Assembly

More documents

Recommendations

Info

• Cut off the fiber, sticking out of the ferrule. In case of a glass fiber, use special cleave tool. • Polish optical fiber cable in minimal two steps (rough and then fine polish) according the termination instruction. Use a polishing holder to align the connector to the polishing pad and polish it with movements in a shape 8. • Remove all traces of abrasive material. • Check the quality of the optical surface with a portable Inspection microscope. Make sure that the surface is free of dirt, debris or damage. • Check the correct mounting of the connector by measuring the attenuation of the cable with the assembled connectors. (Se PROFINET Commissioning PROFINET cable assembly work © Copyright by PNO 2009 – all rights reserved Good Surface 67/99
Guideline for further details • Protect the assembled connector by attaching dust caps • Mate the two parts of the SC-RJ connector into the frame to create the duplex connector. Observe the manufacturers instruction how to place the transmitting and the receiving part of the connector into the frame. As a support the PROFINET FO cable has indicators printed on the cable, that show the transmission direction. PROFINET cable assembly work 68/99 © Copyright by PNO 2009 – all rights reserved Kodiernase
Page 1 and 2:
PROFINET Installation Guideline for
Page 3 and 4:
PROFINET Order No: 8.072 Identifica
Page 5 and 6:
Table of contents 1. Laying PROFINE
Page 7 and 8:
List of figures Figure 1: Cable dis
Page 9 and 10:
Safety instructions The use of the
Page 11 and 12:
Liability exclusion The PROFIBUS Us
Page 13 and 14:
Symbols This document contains vari
Page 15 and 16:
This page is intentionally left bla
Page 17 and 18: Laying PROFINET cables 1.1 Routing
Page 19 and 20: How to read the table Laying PROFIN
Page 21 and 22: • Metallic conductive cable ducts
Page 23 and 24: If the cables are laid in metallic
Page 25 and 26: Laying PROFINET cables Only use app
Page 27 and 28: This page is intentionally left bla
Page 29 and 30: • In areas where people can step
Page 31 and 32: • Store and transport the cable r
Page 33 and 34: • Carefully unreel the PROFINET c
Page 35 and 36: 1.3.8 Distortion • Distortion, an
Page 37 and 38: Laying PROFINET cables 1.3.11 Keepi
Page 39 and 40: Laying PROFINET cables 1.3.13 Avoid
Page 41 and 42: Laying PROFINET cables 1.5.1 Laying
Page 43 and 44: • If copper PROFINET cables are l
Page 45 and 46: PROFINET cable assembly work 2.1 PR
Page 47 and 48: PROFINET cable assembly work Note t
Page 49 and 50: Manuf. instructions PROFINET cable
Page 51 and 52: • Push down the retainer. • Clo
Page 53 and 54: • Open the connector. • Slide t
Page 55 and 56: PROFINET cable assembly work 2.1.5
Page 57 and 58: • Push the two parts of the conne
Page 59 and 60: Manuf. instructions PROFINET cable
Page 63 and 64: PROFINET cable assembly work The ne
Page 65 and 66: PROFINET cable assembly work For mu
Page 67: • Strip the FO cable sheath. •
Page 71 and 72: • Strip the external jacket and t
Page 73 and 74: Optical measurement PROFINET cable
Page 75 and 76: PROFINET cable assembly work As pro
Page 77 and 78: • Interconnect all shields and gr
Page 79 and 80: • Connect the metal cable trays t
Page 83 and 84: • Do not use the shield connectio
Page 85 and 86: This page is intenionally left blan
Page 87 and 88: Connecting PROFINET nodes 3.1.1 Ele
Page 89 and 90: • Due to its design, it is normal
Page 91 and 92: This page is intentionally left bla
Page 93 and 94: Glossary Terms and definitions Comm
Page 95 and 96: Terms and definitions Optical trans
Page 97 and 98: Alphabetic index 96/99 © Copyright
Page 99 and 100: 98/99 © Copyright by PNO 2009 - al
Page 101: Order No.: 8.072 01/2009 © Copyrig
show all

PROFINET Installation Guideline for Cabling and Assembly

Create successful ePaper yourself

Delete template?

Save as template?