PROFINET Installation Guideline for Cabling and Assembly

More documents

Recommendations

Info

PROFINET cable assembly work Observe the following when establishing the shield connection: • Remove the PROFINET cable sheath only for the required connection length. The PROFINET cable is susceptible to mechanical damage in the area where the sheath has been removed. • Be careful not damage the shield when stripping off the PROFINET cable sheath. © Copyright by PNO 2009 – all rights reserved OK No 81/99
• Do not use the shield connection as a strain relief. This would impair the contact between the shield and the equipotential bonding bar. Exception: installation elements specifically application. designed for this • Secure the PROFINET cable before and after the position of shield application. The PROFINET cable which is sensitive in this region can thus be protected against buckling and bending. Pay particular attention to strain relied when the cable is subjected to movement, . PROFINET cable assembly work • Use only connection elements that are appropriate for the diameter of the stripped cable. • Do not attach the equipotential bonding bar to coated surfaces. Galvanized or chromed surfaces, for example, are well suited. • Use tinned, galvanized or otherwise galvanically treated installation material. This is protected against corrosion and establishes permanent, good contact. 82/99 © Copyright by PNO 2009 – all rights reserved No strain relief!
Page 1 and 2:
PROFINET Installation Guideline for
Page 3 and 4:
PROFINET Order No: 8.072 Identifica
Page 5 and 6:
Table of contents 1. Laying PROFINE
Page 7 and 8:
List of figures Figure 1: Cable dis
Page 9 and 10:
Safety instructions The use of the
Page 11 and 12:
Liability exclusion The PROFIBUS Us
Page 13 and 14:
Symbols This document contains vari
Page 15 and 16:
This page is intentionally left bla
Page 17 and 18:
Laying PROFINET cables 1.1 Routing
Page 19 and 20:
How to read the table Laying PROFIN
Page 21 and 22:
• Metallic conductive cable ducts
Page 23 and 24:
If the cables are laid in metallic
Page 25 and 26:
Laying PROFINET cables Only use app
Page 27 and 28:
This page is intentionally left bla
Page 29 and 30:
• In areas where people can step
Page 31 and 32: • Store and transport the cable r
Page 33 and 34: • Carefully unreel the PROFINET c
Page 35 and 36: 1.3.8 Distortion • Distortion, an
Page 37 and 38: Laying PROFINET cables 1.3.11 Keepi
Page 39 and 40: Laying PROFINET cables 1.3.13 Avoid
Page 41 and 42: Laying PROFINET cables 1.5.1 Laying
Page 43 and 44: • If copper PROFINET cables are l
Page 45 and 46: PROFINET cable assembly work 2.1 PR
Page 47 and 48: PROFINET cable assembly work Note t
Page 49 and 50: Manuf. instructions PROFINET cable
Page 51 and 52: • Push down the retainer. • Clo
Page 53 and 54: • Open the connector. • Slide t
Page 55 and 56: PROFINET cable assembly work 2.1.5
Page 57 and 58: • Push the two parts of the conne
Page 59 and 60: Manuf. instructions PROFINET cable
Page 61 and 62: PROFINET cable assembly work 2.2.3
Page 63 and 64: PROFINET cable assembly work The ne
Page 65 and 66: PROFINET cable assembly work For mu
Page 67 and 68: • Strip the FO cable sheath. •
Page 69 and 70: Guideline for further details • P
Page 71 and 72: • Strip the external jacket and t
Page 73 and 74: Optical measurement PROFINET cable
Page 75 and 76: PROFINET cable assembly work As pro
Page 77 and 78: • Interconnect all shields and gr
Page 79 and 80: • Connect the metal cable trays t
Page 81: PROFINET cable assembly work 2.3.7
Page 85 and 86: This page is intenionally left blan
Page 87 and 88: Connecting PROFINET nodes 3.1.1 Ele
Page 89 and 90: • Due to its design, it is normal
Page 91 and 92: This page is intentionally left bla
Page 93 and 94: Glossary Terms and definitions Comm
Page 95 and 96: Terms and definitions Optical trans
Page 97 and 98: Alphabetic index 96/99 © Copyright
Page 99 and 100: 98/99 © Copyright by PNO 2009 - al
Page 101: Order No.: 8.072 01/2009 © Copyrig
show all

PROFINET Installation Guideline for Cabling and Assembly

Create successful ePaper yourself

Delete template?

Save as template?