Modeles 4370 UR1800 Recorder Instruction Manual

More documents

Recommendations

Info

9.10 How to Change Key-lock Settings You can choose to use the key-lock or not. ‘NOT’ : all keys are operable, even when the key is removed from the key-hole. ‘USE’ : to select to ‘USE’ the key-lock affects the 3 modes in different ways. Operation Mode: • Even if you disable the keys (by removing the key from the key-hole), you can still change displays (as in 5.3.8). • If you disable the keys (by removing the key from the key-hole), you cannot operate FUNC in the Operation Mode. • The keys RCD/PRINT/ALARM ACK/FEED can be unlocked/locked individually. SET Mode: If you disable the keys (by removing the key from the key-hole), you cannot enter the SET Mode. If you try, the display will not change. SET UP Mode: Even if you disable the keys (by removing the key from the key-hole), you can always enter and operate the SET UP Mode. The initial values are ‘NOT’ and ‘LOCK’ for all keys. SETTING PROCEDURE: Enter the SET UP Mode by turning ‘ON’ the power while pressing and holding the ENT-key until the SET UP display appears. Use the UP/DOWN-keys to select the display ‘SETUP=LOCK’. Press the ENT-key. Select to USE the key-lock or NOT. Press the ENT-key. In the case you selected NOT, the setting is completed. Select for the RCD, FEED, ALARM ACK and PRINT-key respectively to have them LOCKed or to have them FREE. Press the ENT-key after each selection. The display ‘*LOCK SET*’ will appear. This setting has been completed, but has not been stored yet. You can now adjust other settings in the SET UP Mode, by using the ESC-key. Before leaving the SET UP Mode, you have to store your new settings. Press the ESCkey to return to the ‘SETUP=LOCK’ display and then select the ‘SETUP=END’ display. Press the ENT-key. Select ‘END=STORE’ to keep your new settings or ‘END=ABORT’ and press the ENT-key. After a few seconds, the Operation Mode will appear. 9 - 24 IM 4H3B1-01E
Chapter 10 GENERAL SPECIFICATIONS MODELS 1, 2, 3 and 4 pen; 6 dot, 12 dot, 18dot and 24 dot printing model TYPES DCV : Direct Voltage input 20mV to 20V range. TC : Thermocouple. RTD : Resistance Temperature Detector. DI : Digital Input (contact or DC Voltage, TTL level). DCA : Direct Current Input (using external shunt resistor (10Ω, 100Ω, 250Ω)). IM 4H3B1-01E Measuring Range: selectable per channel Input Type Range Measuring Range DCV 20mV –20.00 to 20.00mV 60mV –60.00 to 60.00mV 200mV –200.0 to 200.0mV 2V –2.000 to 2.000V 6V –6.000 to 6.000V 20V –20.00 to 20.00V TC Range Measuring Range °C Measuring Range °F R *1 0.0 to 1760.0°C 32 to 3200°F S *1 0.0 to 1760.0°C 32 to 3200°F B *1 0.0 to 1820.0°C 32 to 3308°F K *1 –200.0 to 1370.0°C –328 to 2498°F E *1 –200.0 to 800.0°C –328.0 to 1472.0°F J *1 –200.0 to 1100.0°C –328.0 to 2012.0°F T *1 –200.0 to 400.0°C –328.0 to 752.0°F N*2 0.0 to 1300.0°C 32 to 2372°F W*3 0.0 to 2315.0°C 32 to 4199°F L *4 –200.0 to 900.0°C –328.0 to 1652.0°F U *4 –200.0 to 400.0°C –328.0 to 752.0°F PLT 0.0 to 1400.0°C 32 to 2552.0°F PR 0.0 to 1900.0°C 32 to 3452.0°F RTD Range Measuring Range °C Measuring Range °F PT100 *5 –200.0 to 600.0°C –328.0 to 1112.0°F JPT100 *5 –200.0 to 550.0°C –328.0 to 1022.0°F JP50 –200.0 to 600.0°C –328.0 to 1112.0°F CU1 to 6 (Cu10) –200.0 to 300.0°C –328.0 to 572.0°F CU25 (Cu25) –200.0 to 300.0°C –328.0 to 572.0°F DI Range Measuring Range (Digital Input) Voltage input less than 2.4V is OFF, more than 2.4V is ON(TTL) Contact input contact ON/OFF *1 R, S, B, K, E, J, T: ANSI, IEC 584, DIN IEC 584, JIS C 1602-1981 *2 N: Nicrosil-Nisil, IEC 584, DIN IEC 584 *3 W: W·5%Re / W·26%Re (Hoskins Mfg. Co.) *4 L: Fe-CuNi, DIN 43710 U: Cu-CuNi, DIN 43710 *5 PT100: JIS C 1604-1989, JIS C 1606-1989, IEC 751, DIN IEC 751 JPT100: JIS C 1604-1981, JIS C 1606-1989 10 - 1 10. GENERAL SPECIFICATIONS
Page 1 and 2:
Instruction Manual Yokogawa Electri
Page 3 and 4:
SAFETY PRECAUTIONS WARNING CAUTION
Page 7 and 8:
HOW TO USE THIS MANUAL This manual
Page 9 and 10:
1.2 Summary of Functions This parag
Page 11 and 12:
DISPLAY Left-referenced bargraph: m
Page 13:
2.2 Checking the Contents This µR1
Page 16 and 17:
3.1.2 Mounting 1 The µR1800 should
Page 21 and 22:
Pen Model IM 4H3B1-01E - - + + 1 ch
Page 26 and 27:
Chapter 4 COMPONENT NAMES AND FUNCT
Page 28 and 29:
IM 4H3B1-01E 4.1 Front Panel ALARM
Page 30 and 31:
Chapter 5 DAILY OPERATION IM 4H3B1-
Page 32 and 33:
IM 4H3B1-01E 8 Place the rear chart
Page 34 and 35:
CAUTION IM 4H3B1-01E In case of plo
Page 36 and 37:
5.3 Basic Operation (Operation Mode
Page 38 and 39:
IM 4H3B1-01E Figure 5.11b List Prin
Page 40 and 41:
IM 4H3B1-01E Figure 5.12b SET UP Li
Page 42 and 43:
5.3.7 How to Acknowledge an Alarm W
Page 44 and 45:
IM 4H3B1-01E How to select the desi
Page 46 and 47:
5.4 How to Use the Key-lock CAUTION
Page 48 and 49:
6.2 Concept of Setting Parameters P
Page 50 and 51:
6.3.2 Flow Chart of SET Mode This f
Page 52 and 53:
6.4 Setting Parameters in SET Mode
Page 54: Chapter 7 BASIC SETTINGS IM 4H3B1-0
Page 63: 7.2 How to Set Alarms Alarms can be
Page 70 and 71: PRINT PRINT PRINT PRINT PRINT IM 4H
Page 72: 8.1.1 How to Adjust the Trend Recor
Page 76: 8.2 Settings for Digital Printing T
Page 82 and 83: 9.1.1 How to Select the Reflash Fun
Page 84 and 85: 9.1.3 How to Select the Output Rela
Page 86 and 87: 9.1.5 How to Select the Alarm Indic
Page 88 and 89: 9.1.7 How to Select Alarm Hysteresi
Page 90 and 91: 9.2.2 How to Set Upscale/Downscale
Page 92 and 93: 9.2.4 How to Select the Input Filte
Page 94 and 95: 9.3 How to Change Initial Settings
Page 98 and 99: 9.4.5 How to Select Alarm Settings
Page 100 and 101: 9.5 How to Select the Type of Bargr
Page 106 and 107: Calculation: Differential computati
Page 108 and 109: Recording Period: pen : Continuous
Page 110: Alarm Indication When ALARM ACK-key
Page 113 and 114: IM 4H3B1-01E Recording: within ±(5
Page 116 and 117: 11.3 Pen Adjustment (Pen Model) IM
Page 118 and 119: 11.5 Calibration IM 4H3B1-01E It is
Page 120: 11.6 Cleaning the Plotter Carriage
Page 123 and 124: IM 4H3B1-01E The input value and me
Page 125 and 126: TERMINOLOGY allowable input voltage
Page 127 and 128: INDEX A A/D integration time ......
Page 129: ate-of-change High/Low alarm ......
show all

Modeles 4370 UR1800 Recorder Instruction Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?