Modeles 4370 UR1800 Recorder Instruction Manual
Modeles 4370 UR1800 Recorder Instruction Manual
Modeles 4370 UR1800 Recorder Instruction Manual
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
IM 4H3B1-01E<br />
9.4 How to Change Initial Settings for Digital Printouts<br />
If you selected INT:<br />
The display ‘START=00:00’ will appear. Specify the reference time of the first<br />
periodic printout using the UP/DOWN-keys. Press the ENT-key. Note that you cannot<br />
specify minutes.<br />
Specify which interval between the periodic printouts you prefer. Choose from AUTO<br />
(and the interval depends on the chart speed) or MAN (and you can specify the interval<br />
yourself). Then press the ENT-key. Note that in case of AUTO, the relation between the<br />
chart speed and the printing intervals of periodic printouts will be as shown in the tables<br />
below.<br />
Pen Model<br />
Dot Model<br />
Chart Speed Printing Interval of Periodic Printout<br />
5 to 9 mm/h<br />
10 to 18 mm/h<br />
20 to 36 mm/h<br />
40 to 72 mm/h<br />
75 to 135 mm/h<br />
150 to 180 mm/h<br />
200 to 320 mm/h<br />
360 to 1500 mm/h<br />
more than 1500 mm/h<br />
no printout<br />
every 8 hours<br />
every 4 hours<br />
every 2 hours<br />
every hour<br />
every 30 minutes<br />
every 20 minutes<br />
every 10 minutes<br />
no printout<br />
Chart Speed Printing Interval of Periodic Printout<br />
6 dot 12 dot 18 dot 24 dot<br />
1 to 9 mm/h no printout no printout no printout no printout<br />
10 to 19 mm/h every 8 hrs. every 12 hrs. every 12 hrs. every 24 hrs.<br />
20 to 39 mm/h every 4 hrs. every 8 hrs. every 8 hrs. every 12 hrs.<br />
40 to 50 mm/h every 2 hrs. every 4 hrs. every 4 hrs. every 8 hrs.<br />
51 to 79 mm/h every 2 hrs. every 4 hrs. no printout no printout<br />
80 to 100 mm/h every hour every 2 hrs. no printout no printout<br />
101 to 1500 mm/h no printout no printout no printout no printout<br />
If you selected MAN:<br />
Specify the interval using the UP/DOWN-keys. You can choose from 10, 15, 20, 30<br />
min and 1, 2, 3, 4, 6, 8, 12, 24 hrs. Then press the ENT-key. Note that when the<br />
printing takes more time than the specified interval, printouts may be skipped.<br />
This setting has been completed, but has not been stored yet.<br />
The display ‘*RCD SET*’ will appear. You can now adjust other settings in the SET<br />
UP Mode, by using the ESC-key.<br />
If you selected EXT:<br />
The setting has been completed, but has not been stored yet. The display ‘*RCD SET*’<br />
will appear. You can now adjust other settings in the SET UP Mode, by using the ESCkey.<br />
Make sure to specify this also at the settings of the REMOTE option (see 9.8).<br />
Before leaving the SET UP Mode, you have to store your new settings. Press the ESCkey<br />
to return to the ‘SETUP=RCD’ display and then select the ‘SETUP=END’<br />
display.<br />
Press the ENT-key. Select ‘END=STORE’ to keep your new settings or<br />
‘END=ABORT’ and press the ENT-key. After a few seconds, the Operation Mode will<br />
appear.<br />
9 - 19<br />
9. CHANGING INITIAL SETTINGS