Modeles 4370 UR1800 Recorder Instruction Manual

More documents

Recommendations

Info

IM 4H3B1-01E How to select the desired display is described below. 5.3 Basic Operation (Operation Mode) Starting from the basic operation display, press the MENU-key. Select the display ‘MENU=SELECT_DISPLAY’ using the UP/DOWN-keys. Then press the ENT-key. You have now entered the following flow: DISPLAY_AUTO DISPLAY_MANUAL MANUAL CH=? DISPLAY_CLOCK DISPLAY_VIEW Moving between the different displays can be done by using the UP/DOWN-keys. Once you selected the desired display, press the ENT-key (In the case of the manual display, select the channel number by using the UP/DOWN-keys. Then press the ENTkey again). After having pressed the ENT-key, the selected display will appear. If you want to change the channel number while displaying the measured values on the manual display, you can change the channel number by pressing the ENT-key. 5 - 15 5. DAILY OPERATION
5.3.9 How to Cope with FAIL/Chart End When equipped with this option and the chart reaches its end or a CPU-error occurs, the output relay will be activated. There is one output relay for Chart end detection, and one for FAIL detection. For the wiring, see 3.2.5. CHART END: When there are approx. 2cm left till chart end, the ‘CHT’ indicator will be illuminated in the display and recording will stop. To change the chart, follow the steps as explained in 5.2.1. At the same time the output relay will be activated. This output relay is of the energizing type and this cannot be changed. See also the explanation mentioned below. FAIL: When a CPU-error occurs, the output relay will be activated. This relay is of the deenergizing type and this cannot be changed. Therefore this relay will also be activated when the power is off. The activating of this relay will not be shown on the display. See also the explanation mentioned below. When a CPU-error occurs, contact the nearest Sales & Service Office. Addresses may be found on the back cover of this manual. Explanation: Chart end output relay (energize type): NO C NC Normal operation NO C NC Chart end occurs FAIL output relay (de-energize type): NO C NC Normal operation NO C NC Chart end occurs (FAIL) NO C NC Power OFF NO C NC Power OFF 5 - 16 IM 4H3B1-01E
Page 1 and 2: Instruction Manual Yokogawa Electri
Page 3 and 4: SAFETY PRECAUTIONS WARNING CAUTION
Page 7 and 8: HOW TO USE THIS MANUAL This manual
Page 9 and 10: 1.2 Summary of Functions This parag
Page 11 and 12: DISPLAY Left-referenced bargraph: m
Page 13: 2.2 Checking the Contents This µR1
Page 16 and 17: 3.1.2 Mounting 1 The µR1800 should
Page 21 and 22: Pen Model IM 4H3B1-01E - - + + 1 ch
Page 26 and 27: Chapter 4 COMPONENT NAMES AND FUNCT
Page 28 and 29: IM 4H3B1-01E 4.1 Front Panel ALARM
Page 30 and 31: Chapter 5 DAILY OPERATION IM 4H3B1-
Page 32 and 33: IM 4H3B1-01E 8 Place the rear chart
Page 34 and 35: CAUTION IM 4H3B1-01E In case of plo
Page 36 and 37: 5.3 Basic Operation (Operation Mode
Page 38 and 39: IM 4H3B1-01E Figure 5.11b List Prin
Page 40 and 41: IM 4H3B1-01E Figure 5.12b SET UP Li
Page 42 and 43: 5.3.7 How to Acknowledge an Alarm W
Page 46 and 47: 5.4 How to Use the Key-lock CAUTION
Page 48 and 49: 6.2 Concept of Setting Parameters P
Page 50 and 51: 6.3.2 Flow Chart of SET Mode This f
Page 52 and 53: 6.4 Setting Parameters in SET Mode
Page 54: Chapter 7 BASIC SETTINGS IM 4H3B1-0
Page 63: 7.2 How to Set Alarms Alarms can be
Page 70 and 71: PRINT PRINT PRINT PRINT PRINT IM 4H
Page 72: 8.1.1 How to Adjust the Trend Recor
Page 76: 8.2 Settings for Digital Printing T
Page 82 and 83: 9.1.1 How to Select the Reflash Fun
Page 84 and 85: 9.1.3 How to Select the Output Rela
Page 86 and 87: 9.1.5 How to Select the Alarm Indic
Page 88 and 89: 9.1.7 How to Select Alarm Hysteresi
Page 90 and 91: 9.2.2 How to Set Upscale/Downscale
Page 92 and 93: 9.2.4 How to Select the Input Filte
Page 94 and 95:
9.3 How to Change Initial Settings
Page 96 and 97:
Page 98 and 99:
9.4.5 How to Select Alarm Settings
Page 100 and 101:
9.5 How to Select the Type of Bargr
Page 102 and 103:
Page 104 and 105:
9.10 How to Change Key-lock Setting
Page 106 and 107:
Calculation: Differential computati
Page 108 and 109:
Recording Period: pen : Continuous
Page 110:
Alarm Indication When ALARM ACK-key
Page 113 and 114:
IM 4H3B1-01E Recording: within ±(5
Page 116 and 117:
11.3 Pen Adjustment (Pen Model) IM
Page 118 and 119:
11.5 Calibration IM 4H3B1-01E It is
Page 120:
11.6 Cleaning the Plotter Carriage
Page 123 and 124:
IM 4H3B1-01E The input value and me
Page 125 and 126:
TERMINOLOGY allowable input voltage
Page 127 and 128:
INDEX A A/D integration time ......
Page 129:
ate-of-change High/Low alarm ......
show all

Modeles 4370 UR1800 Recorder Instruction Manual

Create successful ePaper yourself

Delete template?

Save as template?