Modeles 4370 UR1800 Recorder Instruction Manual

More documents

Recommendations

Info

CAUTION IM 4H3B1-01E In case of plotter pen: 1 Open the front door and make sure the recording is not in progress (by pressing the RCD-key; power can be either ‘ON’ or ‘OFF’). 2 Swing up the display by grasping and pulling the tabs located at the lower left and right corner. 3 While grasping the plotter holder, gently slide the plotter out of the holder (see figure 5.8). 4 Remove the pen cap and insert a new plotter pen in the holder (see figure 5.8). If it is difficult to replace the plotter pen, try the 2nd procedure as described above. 5 Close the display by pulling the 'release'-handle until this handle is at the same level as the display. Then push the display back into its normal position until the tabs click shut. Plotter pen Figure 5.8 In case of the ribbon cassette: 1 Open the front door and make sure the power is OFF. 2 Swing up the display by grasping and pulling the tabs located at the lower left and right corner. 3 Hold the back section of the carriage assembly and move the assembly to the right. 4 Press the lock tab to the right and use the lower left part of the cassette as a handle to pull it out of the holder. See figure 5.9. Figure 5.9 5.2 How to Install (& Replace) Chart, Pens, Ribbon Cassette and Battery Pen holder Ribbon cassette Printer carriage 5 Insert the right side of the new ribbon cassette into the cassette holder. 6 Insert the left side of the ribbon cassette into the cassette holder (clicking it into its place). If the ribbon cassette does not click into its place easily, adjust the ribbon feeding knob so that the peg fits the hole. 7 If necessary, turn the ribbon feeding knob to stretch/tighten the ribbon. 8 Close the display by pulling the 'release'-handle until this handle is at the same level as the display. Then push the display back into its normal position until the tabs click shut. If the ribbon cassette is not inserted correctly: • data may be printed in the wrong color • ribbon edge is used to print out data, which damages the ribbon. 5 - 5 5. DAILY OPERATION
5.2.3 How to Replace the Battery The ‘BAT’ indicator on the VFD-display can either remain illuminated or flash. In case of illumination, the lithium battery needs to be replaced. However, this battery will last for ten years under normal operation conditions. For replacement, please contact the nearest Sales & Service Office. Addresses may be found on the back cover of this manual. In case of flashing, you have to replace your IC Memory Card battery (option). In case of replacement, please refer to the IC Memory Card <strong>Instruction</strong> <strong>Manual</strong> IM 4H3B1-30E. WARNING To avoid injury, never replace the lithium battery yourself. 5 - 6 IM 4H3B1-01E
Page 1 and 2: Instruction Manual Yokogawa Electri
Page 3 and 4: SAFETY PRECAUTIONS WARNING CAUTION
Page 7 and 8: HOW TO USE THIS MANUAL This manual
Page 9 and 10: 1.2 Summary of Functions This parag
Page 11 and 12: DISPLAY Left-referenced bargraph: m
Page 13: 2.2 Checking the Contents This µR1
Page 16 and 17: 3.1.2 Mounting 1 The µR1800 should
Page 21 and 22: Pen Model IM 4H3B1-01E - - + + 1 ch
Page 26 and 27: Chapter 4 COMPONENT NAMES AND FUNCT
Page 28 and 29: IM 4H3B1-01E 4.1 Front Panel ALARM
Page 30 and 31: Chapter 5 DAILY OPERATION IM 4H3B1-
Page 32 and 33: IM 4H3B1-01E 8 Place the rear chart
Page 36 and 37: 5.3 Basic Operation (Operation Mode
Page 38 and 39: IM 4H3B1-01E Figure 5.11b List Prin
Page 40 and 41: IM 4H3B1-01E Figure 5.12b SET UP Li
Page 42 and 43: 5.3.7 How to Acknowledge an Alarm W
Page 44 and 45: IM 4H3B1-01E How to select the desi
Page 46 and 47: 5.4 How to Use the Key-lock CAUTION
Page 48 and 49: 6.2 Concept of Setting Parameters P
Page 50 and 51: 6.3.2 Flow Chart of SET Mode This f
Page 52 and 53: 6.4 Setting Parameters in SET Mode
Page 54: Chapter 7 BASIC SETTINGS IM 4H3B1-0
Page 63: 7.2 How to Set Alarms Alarms can be
Page 70 and 71: PRINT PRINT PRINT PRINT PRINT IM 4H
Page 72: 8.1.1 How to Adjust the Trend Recor
Page 76: 8.2 Settings for Digital Printing T
Page 82 and 83: 9.1.1 How to Select the Reflash Fun
Page 84 and 85:
9.1.3 How to Select the Output Rela
Page 86 and 87:
9.1.5 How to Select the Alarm Indic
Page 88 and 89:
9.1.7 How to Select Alarm Hysteresi
Page 90 and 91:
9.2.2 How to Set Upscale/Downscale
Page 92 and 93:
9.2.4 How to Select the Input Filte
Page 94 and 95:
9.3 How to Change Initial Settings
Page 96 and 97:
Page 98 and 99:
9.4.5 How to Select Alarm Settings
Page 100 and 101:
9.5 How to Select the Type of Bargr
Page 102 and 103:
Page 104 and 105:
9.10 How to Change Key-lock Setting
Page 106 and 107:
Calculation: Differential computati
Page 108 and 109:
Recording Period: pen : Continuous
Page 110:
Alarm Indication When ALARM ACK-key
Page 113 and 114:
IM 4H3B1-01E Recording: within ±(5
Page 116 and 117:
11.3 Pen Adjustment (Pen Model) IM
Page 118 and 119:
11.5 Calibration IM 4H3B1-01E It is
Page 120:
11.6 Cleaning the Plotter Carriage
Page 123 and 124:
IM 4H3B1-01E The input value and me
Page 125 and 126:
TERMINOLOGY allowable input voltage
Page 127 and 128:
INDEX A A/D integration time ......
Page 129:
ate-of-change High/Low alarm ......
show all

Modeles 4370 UR1800 Recorder Instruction Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?