CLI Guide - TP-Link

More documents

Recommendations

Info

TL-SL3428/TL-SL3452 JetStream L2 Managed Switch CLI Guide Chapter 19 Ethernet Configuration Commands Ethernet Configuration Commands can be used to configure the Bandwidth Control, Negotiation Mode and Storm Control for Ethernet ports. interface ethernet Description The interface ethernet command is used to enter the Interface Configuration Mode and configure one Ethernet port. Syntax interface ethernet interface Parameter interface —— The Ethernet port to be configured. Command Mode Global Configuration Mode Example Enter the Interface Configuration Mode and configure Ethernet port2: TP-LINK(config)# interface ethernet 2 interface range ethernet Description The interface range ethernet command is used to enter the Interface Configuration Mode and configure multiple Ethernet ports at the same time. Syntax interface range ethernet port-list Parameter port-list —— The list of the Ethernet ports to be configured. Inconsecutive ports or port-groups are separated by a comma with no space. Use a hyphen to designate a range of ports, for instance 1-10 indicates from port 1 to port 10. Command Mode Global Configuration Mode User Guidelines 110
TL-SL3428/TL-SL3452 JetStream L2 Managed Switch CLI Guide Command in the Interface Range Ethernet Mode is executed independently on all ports in the range. It does not effect the execution on the other ports at all if the command results in an error on one port. Example Enter the Interface Configuration Mode, add ports 1-3, 6-9 to the port-list and configure them: TP-LINK(config)# interface range ethernet 1-3,6-9 description Description The description command is used to add a description to the Ethernet port. To clear the description of the corresponding port, please use no description command. Syntax description string no description Parameter string —— Content of a port description, ranging from 1 to 16 characters. Command Mode Interface Configuration Mode(interface Ethernet) Example Add a description Port #5 to port5: TP-LINK(config)# interface ethernet 5 TP-LINK(config-if)# description Port #5 shutdown Description The shutdown command is used to disable an Ethernet port. To enable this port again, please use no shutdown command. Syntax shutdown no shutdown 111
Page 1 and 2:
TL-SL3428/TL-SL3452 JetStream L2 Ma
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
switchport voice-vlan mode TL-SL342
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
user modify type TL-SL3428/TL-SL345
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72: TL-SL3428/TL-SL3452 JetStream L2 Ma
Page 75 and 76: show arp detection statistic TL-SL3
Page 93 and 94: logging local flash TL-SL3428/TL-SL
Page 107 and 108: idge aging-time TL-SL3428/TL-SL3452
Page 113 and 114: ip management-vlan TL-SL3428/TL-SL3
Page 115 and 116: user-config backup TL-SL3428/TL-SL3
Page 121: TL-SL3428/TL-SL3452 JetStream L2 Ma
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
snmp view-add TL-SL3428/TL-SL3452 J
Page 185 and 186:
snmp user-add TL-SL3428/TL-SL3452 J
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
show snmp-rmon alarm TL-SL3428/TL-S
Page 201 and 202:
Page 203 and 204:
cluster manage role-change TL-SL342
Page 205 and 206:
show all

CLI Guide - TP-Link

Create successful ePaper yourself

Delete template?

Save as template?