CLI Guide - TP-Link

More documents

Recommendations

Info

TL-SL3428/TL-SL3452 JetStream L2 Managed Switch CLI Guide options. None indicates no privacy method is used, and DES indicates DES encryption method is used. By default, the Privacy Mode is none. encrypt-pwd —— Privacy Password, ranging from 1 to 16 characters. Command Mode Global Configuration Mode Example Add User admin to Group group2, and configure the Security Model of the user as v3, the Security Level of the group as authPriv, the Authentication Mode of the user as MD5, the Authentication Password as 11111, the Privacy Mode as DES, and the Privacy Password as 22222: TP-LINK(config)# snmp user-add admin local group2 smode v3 slev authPriv cmode MD5 cpwd 11111 emode DES epwd 22222 snmp community-add Description The snmp community-add command is used to add Community. To delete the corresponding Community, please use no snmp community-add command. SNMP v1 and SNMP v2c adopt community name authentication. The community name can limit access to the SNMP agent from SNMP network management station, functioning as a password. Syntax snmp community-add {name} { read-only | read-write } {mib-view} no snmp community-add {name} Parameter name —— Community Name, ranging from 1 to 16 characters. read-only | read-write —— The access rights of the community, with read-only and read-write options. mib-view —— The MIB View for the community to access. Command Mode Global Configuration Mode Example Add Community community1, and the community has read-write management right to View view1: 174
TL-SL3428/TL-SL3452 JetStream L2 Managed Switch CLI Guide TP-LINK(config)# snmp community-add community1 read-write view1 snmp notify-add Description The snmp notify-add command is used to add Notification. To delete the corresponding Notification, please use no snmp notify-add command. With the Notification function enabled, the switch can initiatively report to the management station about the important events that occur on the Views, which allows the management station to monitor and process the events in time. Syntax snmp notify-add {ip} {udp-port} {user-name} [smode { v1 | v2c | v3 }] [slev { noAuthNoPriv | authNoPriv | authPriv }] [type { trap | inform }] [resend resend] [timeout timeout] no snmp notify-add {ip} {user-name} Parameter ip —— The IP Address of the management Host. udp-port —— UDP port, which is used to send notifications. The UDP port functions with the IP address for the notification sending. By default, it is 162. user-name —— The User name of the management station. smode —— The Security Model of the management station, with v1, v2c and v3 options. By default, the option is v1. slev —— The Security Level of SNMP v3 Group. There are three options, including noAuthNoPriv (no authorization and no encryption), authNoPriv (authorization and no encryption) and authPriv (authorization and encryption). By default, the option is noAuthNoPriv. type —— The type of the notifications, with trap and inform options. Trap indicates traps are sent, while inform indicates informs are sent. The inform type has a higher security than the trap type and resend and timeout need to be configured if you select this option. You can only select the trap type in Security Model v1. By default, the type of the notifications is trap. resend —— The amount of times the switch resends an inform request, ranging from 1 to 255. The switch will resend the inform request if it doesn’t get the response from the management station during the Timeout interval, and it will terminate resending the inform request if the resending times reach the specified Retry times. 175
Page 1 and 2:
TL-SL3428/TL-SL3452 JetStream L2 Ma
Page 3 and 4:
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
switchport voice-vlan mode TL-SL342
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
user modify type TL-SL3428/TL-SL345
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
show arp detection statistic TL-SL3
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
logging local flash TL-SL3428/TL-SL
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
idge aging-time TL-SL3428/TL-SL3452
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
ip management-vlan TL-SL3428/TL-SL3
Page 115 and 116:
user-config backup TL-SL3428/TL-SL3
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136: TL-SL3428/TL-SL3452 JetStream L2 Ma
Page 183 and 184: snmp view-add TL-SL3428/TL-SL3452 J
Page 185: snmp user-add TL-SL3428/TL-SL3452 J
Page 199 and 200: show snmp-rmon alarm TL-SL3428/TL-S
Page 203 and 204: cluster manage role-change TL-SL342
show all

CLI Guide - TP-Link

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?