ABB i-Bus® EIB/KNX ABB Powernet EIB/KNX
ABB i-Bus® EIB/KNX ABB Powernet EIB/KNX
ABB i-Bus® EIB/KNX ABB Powernet EIB/KNX
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>ABB</strong> i-bus ® <strong>EIB</strong>/<strong>KNX</strong><br />
<strong>ABB</strong> <strong>Powernet</strong> <strong>EIB</strong>/<strong>KNX</strong><br />
LEANtouch (monochrome),<br />
SMARTtouch (monochrome, colour)<br />
Type: 6x36/30M…, 6x36/100x…, 6x36/100CB…<br />
Parameters: Room thermostat<br />
The default setting for the values<br />
is printed in bold type.<br />
Only for cooling:<br />
Setpoints cooling:<br />
– Dead zone between heating and 1…4…8<br />
cooling in K (1…8)<br />
– Increasing standby operation cooling 1…2…8<br />
– Increasing night operation cooling 1…4…8<br />
– Setpoint heat protection Cooling switched off<br />
30°C<br />
35°C<br />
40°C<br />
44°C<br />
Controlling/Control value cooling:<br />
– Output of control value continuously<br />
switched<br />
– Control type Two-position controller<br />
PI controller<br />
Only for two-position controller:<br />
– Hysteresis 0.3K / 0.5K / 0.7K / 1.0K / 1.5K / 2.0K<br />
– Lowering of hysteresis Inactive<br />
0.2 K/min<br />
0.1 K/min<br />
0.06 K/min<br />
0.04 K/min<br />
0.03 K/min<br />
0.02 K/min<br />
– Cycle time of the control value in 04:46<br />
mm:ss (03:00…60:00)<br />
– Effective mode Normal<br />
Inverted<br />
Only for PI controller:<br />
– Control parameters via installation type<br />
free setting of parameters<br />
– Type of cooling system Cooling ceiling (5K/240min)<br />
SplitUnit/Fan cooling (4K/90min)<br />
– PWM cycle 3min / 5min / 10min / 15min / 20min /<br />
30min / 40min / 50min / 60min<br />
– PWM cycle is 0% up to control value 0% / 10% / 20% / 30%<br />
– PWM cycle is 100% up to control value 70% / 80% / 90% / 100%<br />
– Effective mode Normal<br />
Inverted<br />
Only for free parameterisation:<br />
– Proportional area 1.0K / 1.5K / 2.0K / 2.5K / 3K / 4K /<br />
6K / 8K / 10K<br />
– Restet time in min. I part inactive / 10 min / 20 min / …<br />
100 min / … / 200 min / 240 min<br />
Only for continuous controller:<br />
– Cycle time of the control value in mm:ss 04:46<br />
(03:00…60:00)<br />
– Effective mode Normal<br />
Inverted<br />
– Change for automatic sending of Inactive / 2% / 5% / 10%<br />
control value<br />
May 2006 71