Alternative Reader Wiring Guide - Best Access Systems

More documents

Recommendations

Info

Nedap Readers a. for the ASCII Setup: b. Set the communication properties: – BPS: 9600 – Data bits: 7 – Parity: Even – Stop bits: 1 – Flow control: None 3. Check the current settings for the inter ID delay by typing in QC5 (must be in caps) followed by . 4. Change the settings by typing SC532. Press . The screen should return SC532. 5. Once again, you can check these settings by typing in QC5 followed by to make sure the parameters were accepted. Any error will return a question mark (?). 112 — revision 7
Alternative Reader Wiring Guide 22. Secura Key Readers 22.1. e-Tag Prox Reader #ASSY 2014040 This demonstrates the default wiring configuration for the reader. However, there is no control for the LED's or the buzzer. There is no way to tell what state the reader is in from the door. The reader will only flash a green light and beep once when a card is read. There are no other indications of the readers state. 22.1.1 Wiring the BAS-1300 Secura Key (eTag) Prox Reader (ASSY 2014040) e*Tag TM Single Reader Interface Module Black GND Violet BZR Orange LED White CLK/D1 Green DATA/D0 Red VO Secura Key TYPICAL SOFTWARE SETTINGS 1. Reader Type = Wiegand/Prox 2. Keypad = No Keypad 3. LED Mode = 1-wire LED Control revision 7 — 113
Page 3 and 4:
Alternative Reader Wiring Guide Tab
Page 5 and 6:
Alternative Reader Wiring Guide 124
Page 7:
ACCESS READERS
Page 10 and 11:
AIT Readers 1.1.2 Wiring the BAS-13
Page 12 and 13:
AWID Readers 2.1.2 Wiring the BAS-1
Page 14 and 15:
AWID Readers 2.3. AWID PROX with Ke
Page 16 and 17:
AWID Readers 2.4. AWID Sentinel-Pro
Page 18 and 19:
AWID Readers 18 — revision 7
Page 20 and 21:
BAI Barcode Readers 3.1.2 Wiring th
Page 22 and 23:
Banque-Tec Readers 4.1.2 Wiring the
Page 24 and 25:
Baran Tec Keypads Important: Make s
Page 26 and 27:
Baran Tec Keypads 5.2. Barantec Eve
Page 28 and 29:
Baran Tec Keypads 28 — revision 7
Page 30 and 31:
Bewator Readers 6.1.2 Wiring the BA
Page 32 and 33:
Casi-Rusco Prox Readers 7.1.2 Wirin
Page 34 and 35:
Casi-Rusco Prox Readers Status Indi
Page 36 and 37:
Ceia Readers 8.1.2 Wiring the BAS-1
Page 38 and 39:
Checkpoint Systems Readers 9.1.2 Wi
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Deister Electronics 10.1.2 Wiring t
Page 46 and 47:
Dorado Readers 11.1.2 Wiring the BA
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Dorado Readers 52 — revision 7
Page 54 and 55:
Essex Keypads 12.1.2 Wiring the BAS
Page 56 and 57:
Essex Keypads 12.2.2 Wiring the BAS
Page 58 and 59:
HID Readers 13.1.2 Wiring the BAS-1
Page 60 and 61:
HID Readers 13.3. HID MaxiProx 5370
Page 62 and 63: HID Readers 13.4.2 Wiring the BAS-1
Page 74 and 75: HID Readers 13.10.2 Wiring the BAS-
Page 76 and 77: IDH Max Readers 76 — revision 7
Page 78 and 79: ID Solutions Readers 15.1.2 Wiring
Page 80 and 81: Infographics Readers 16.1.2 Wiring
Page 82 and 83: Keri Systems Readers 17.1.2 Wiring
Page 84 and 85: Magtek Readers 18.1.2 Wiring the BA
Page 86 and 87: Mifare Readers 19.1.2 Wiring the BA
Page 88 and 89: Mifare Readers 19.2.2 Wiring the BA
Page 90 and 91: Mifare Readers 19.3. Iolan Reader M
Page 92 and 93: Mifare Readers 92 — revision 7
Page 94 and 95: Motorola Indala Readers 20.1.2 Wiri
Page 106 and 107: Motorola Indala Readers 20.7. Indal
Page 110 and 111: Nedap Readers 21.1.2 Wiring the BAS
Page 114 and 115: Secura Key Readers 22.1.2 Wiring th
Page 120 and 121: Star Wiring Using APM10/11 120 —
Page 122 and 123: Texas Instruments Readers 24.1.2 Wi
Page 124 and 125: Index S Secura Key (e-Tag) prox rea
Page 126: P.O. Box 5044 Indianapolis, IN 4625
show all

Alternative Reader Wiring Guide - Best Access Systems

Create successful ePaper yourself

Delete template?

Save as template?