Medspiration â System Requirements Document - Data User Element

More documents

Recommendations

Info

Medspiration MED-SOC-RS-001_1 System Requirements Document Issue F Page Table, fig. Reference ID Text from reference documents sensor specific error estimates for each pixel value have been included and the original SST data reformatted to netCDF format. SR entry L2P.0050 L2P.0060 46 WP2-042 No modification to the original SST data values has taken place during the conversion process. L2P.0080 47 Footnote 7 WP2-043 Note that in the case of 1km input SST data streams, averaging of these data is permitted to provide data at a resolution of no greater than 1/12° latitude x longitude. In this case, there may be some modification to the original input data. L2P.0090 47 WP2-044 L2P data products will be available to the operational user community in real time and ideally, within 6 hours following PER.SYS.0010 reception at the satellite platform. 47 WP2-045 However, as the GHRSST-PP intends to generate global 1/12° L4 analysed SST data output from L2P data files, high L2P.0090 resolution input data sets may be averaged to a coarser resolution no greater than 1/12°. 47 Figure WP2-046 Functional breakdown of WP-ID2 identifying each major sub task NASR 5.1 47 WP2-047 A functional breakdown diagram for WP-ID2 is shown in Figure 5.1 (additional functional breakdown diagrams are NASR provided for WP-ID2.1, WP-ID2.2 and WP-ID2.5 in the appropriate section below). 47 WP2-048 In a series of pre-processing and quality control procedures, microwave and Infrared Satellite SST data are merged L2P.0030 together with reference data and auxiliary data including satellite and NWP Wind speed, sea ice concentration, surface solar irradiance and aerosol optical depth estimates. 47 WP2-049 If data processing problems are encountered the SST data file is rejected from the GDS, (e.g., values are outside of expected range, overwhelming cloud contamination) an error message is sent to the satellite SST data provider point of ING.0100 QLC.0035 contact (as defined in the GHRSST-PP MMR_DSD record associated with the SST data file) explaining why the SST data have not been used in the GDS. A copy of the message is also sent to the GHRSST-PP error log system (errlog@ghrsstpp.org). 48 WP2-050 If the SST data are accepted into the GDS, L2P additional pixel confidence data are then derived for every SST L2P.0040 © 2004 SOC Page 136 of 193
Medspiration MED-SOC-RS-001_1 System Requirements Document Issue F Page Table, fig. Reference ID Text from reference documents SR entry measurement. L2P confidence data are required to: 48 WP2-051 1. Derive a quantitative ‘confidence value’ for each SST measurement that is used to identify reduced quality data. NASR 48 WP2-052 2. Derive and interpret of SSES values assigned to each SST measurement. NASR 48 WP2-053 3. Force parameterisations that estimate diurnal variability. NASR 48 WP2-054 Using confidence data, Sensor Specific Error Statistics (SSES) are assigned to each SST measurement based on analysis L2P.0050 of the GHRSST-PP Match-up Database (MDB) system described in WP-ID3. 48 WP2-055 A L2P data file is generated (format described in Appendix A1.4) which contains the original SST data together with pixel L2P.0060 confidence data. L2P data files are formatted as GDS netCDF files (WP-ID1.2.3) that are fully described in Appendix A1. 48 WP2-056 For each L2P data file a MMR_FR metadata record (described in Appendix A6) is generated and registered at the MMR ING.0030 under the appropriate MMR_DSD. 48 WP2-057 L2P data files and pixel confidence data are identical in format for all input SST data streams with differs between the IR L2P.0060 and MW SST data exist. Using a single data format for all SST data files greatly facilitates SST inter-comparison and merging activities within the GHRSST-PP. 48 WP-ID2.1 Pre-processing and merging of auxiliary data. 48 WP2-058 This work-package describes in detail common pre-processing operations performed on each IR and MW SST data file. MRG.0020 Figure 5.2.1 provides a functional breakdown diagram that identifies each common pre-processing pixel based operation. These are: 48 WP2-059 Check that the SST value lies within acceptable limits, if not then reject the data file QLC.0070 48 WP2-060 Compute the pixel measurement time ING.0070 48 WP2-061 Assign a fractional sea ice value if required MRG.0030 48 WP2-062 Assign a wind speed value MRG.0040 48 WP2-063 Assign a surface solar irradiance (SSI) value MRG.0050 © 2004 SOC Page 137 of 193
Page 1 and 2:
Medspiration System Requirements Do
Page 3 and 4:
Page 5 and 6:
Medspiration MED-SOC-RS-001_1 Syste
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86: Medspiration System Requirements Do
Page 89 and 90: Medspiration MED-SOC-RS-001_1 Syste
Page 135: Medspiration MED-SOC-RS-001_1 Syste
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193:
show all

Medspiration â System Requirements Document - Data User Element

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?

Medspiration â System Requirements Document - Data User Element