WEIGH SCALE BLENDER® - Maguire Products

More documents

Recommendations

Info

WEIGH SCALE BLENDER® MAGUIRE PRODUCTS, INC. Assembly and Installation Instructions CAUTION: LOAD CELLS ARE EASILY DAMAGED. If the FRAME is dropped from TWO FEET, the load cells WILL BE DAMAGED. THE WARRANTY DOES NOT COVER DAMAGED LOAD CELLS. The following items have been shipped to you: 1. FRAME and HOPPER assembly: (bolted to skid) 2. CONTROLLER BOX: with the instruction manual. 3. FEEDER BOX: contains a COLOR or ADDITIVE feeder: optional. 4. FLOW CONTROL ASSEMBLY: optional 5. FLOOR STAND or VACUUM TAKEOFF ASSEMBLY: optional RED INSTRUCTION STICKERS will assist you during assembly. LIFT HANGERS are available to allow lifting the blender with a strap or chain. Contact Maguire if you require them. 1A. If your unit is to be MACHINE mounted: For WSB MB, 100, 200, and 400 series models: Two ways to do this are suggested ON THE NEXT PAGE: The LEFT diagram shows the FRAME and SLIDE GATE both drilled with the proper bolt pattern for your machine and THROUGH BOLTED to your press. The RIGHT diagram shows only the 10 x 10 steel slide-gate plate drilled for your bolt pattern and bolted to your press. The FRAME is then bolted to it using the existing 8 x 8 inch bolt pattern holes and bolts provided. With this method, bolt head clearance holes are required in the poly-pro slide gate plate. This mounting works well on smaller machines. For WSB 900 and 1800 series models: An additional machine mount adaptor plate may be required. If you have ANY DOUBT about the STABILITY of the unit when bolted directly to your machine throat, please call us for advice. NOTE: When choosing proper orientation, be sure to retain access to the controller and weigh chamber, clearance for hinged doors, and access to removable feeder hoppers. 1B. If your unit is STAND mounted: A stand is provided and your unit will bolt directly to it. An assembly DIAGRAM is provided on the following pages. An air operated FLOW CONTROL ASSEMBLY is provided for dispensing into a container. The purpose of this unit is to allow time for mixing to occur after each dispense. This flow valve keeps the mix chamber full to just below the sensor. This assembly bolts directly to the bottom of the Weigh Scale Blender frame. Edition: March 24, 2008 12
WEIGH SCALE BLENDER® MAGUIRE PRODUCTS, INC. Edition: March 24, 2008 13
Page 1 and 2: MAGUIRE PRODUCTS INC. Weigh Scale B
Page 3 and 4: WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 11: WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 51 and 52: CON TI NUE STOP END OF CYCL E CON T
Page 63 and 64:
WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
show all

WEIGH SCALE BLENDER® - Maguire Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?