WEIGH SCALE BLENDER® - Maguire Products

More documents

Recommendations

Info

REG NAT COL ADD DMP ALM MIX HLD CONTINUE STOP E N D OF CY C LE CONTINUE I ATE C A R COM PUTER PRINTER LOAD CELLS ADDITIVE COLOR REGR IND 1/2 AM P FUSE 3 AMP ON-OFF 120 VOLTS % OF NATURAL % OF NATURAL % OF MIX FUSE WEIGH SCALE BLENDER® MAGUIRE PRODUCTS, INC. Star Functions - What they relate to: *14 *69 *14 *71 *72 *82 *14 *71 *72 *82 *33 *74 *75 *44 *52 *66 *00 *05 *54 *77 *88 CONTINUE STOP END OF CYCLE CONTINUE IMMEDIATE PAUSE COMPUTER PRINTER *47 *48 VIEW RECP BTCH FAST EXIT SET OPER TIME CAL TAG REG 1 2 3 NAT A 4 5 6 COL B 7 8 9 ADD C * 0 CE HOLD DUMP PARA ZERO FULL MIX ALRM TOTAL WEIGHT-GRAMS WEIGH SCALE BLENDER LOCKED OUT ALA RMS 0 0 0 0 0 0 0 0 0 MAGUIRE PRODUCTS, ASTON, PA *03 *04 *87 *99 *02 LOAD CELLS EXTRUSION CONTROL *45 *78 AIR SOLENOID VALVES ADDITIVE COLOR *12*23*32*25 *98 *11 *89 *02 Extrusion and Yield Control *03 Four digit (xx.xx) settings *04 Simulate FOUR software *05 Inhibit table clearing *12 Move table from ROM to RAM *23 Move from RAM to EEPROM *32 Move from EEPROM to RAM *14 Set types: REG, NAT, ADD, OFF *25 ROM OK flag, "CE" to clear *33 Special Alarms *44 End cycle - bin full *45 Change MANUAL mode password *47 Totalizer flag *48 Dispense range xx.x to xxx *52 Double dump weigh bin *54 Print cycle information *66 66 WSB I.D. number (1-255) *72 72 Additive percent of blend *74 74 Stop, alarm MAX wt exceeded *75 75 Alarm on weight drop *77 Print parameters *78 Change program mode password *82 Precision Ratioing *87 VOLUMETRIC operation *88 Print display readout *89 Select pounds, kilos *98 Display raw weight number Use "*" key to select readout or toggle flags ON or OFF Edition: March 24, 2008 42
WEIGH SCALE BLENDER® MAGUIRE PRODUCTS, INC. Star Functions Star Functions are only available in PROGRAM mode: EXTRUDER MODE - Extrusion and Yield Control, and Rate display. Press (*,0,2) to turn on Extrusion or Yield control. The default display is ( OFF). Press * to toggle this flag to ( RATE ), (EXT CTRL), or (YLD CTRL). If you are using our EXTRUSION or YIELD control software to control your extruder, refer to our EXTRUSION CONTROL instruction booklet for complete information. If you simply want to view throughput continuously on the blender display, set this option to ( RATE ). This will alter the display only. In all other respects, the blender will operate normally. YLD-X – Extruder Control YLD-T – Takeoff YLD-D – Dual INPUT FORMAT - 4 Digit Entry of Settings – xx.xx Press (*,0,3) to allow four digit entry of settings in the format (xx.xx). This does not make the blender more accurate. It does allow easier setup for customers that have a mixture of setting requirements that is x.xx entry requirements as well as the standard xx.x requirements. Normally the XT parameter would be manually adjusted to allow the decimal shift. If this fourdigit entry option is turned on, then all entries are in the format xx.xx. The software uses only the first three digits unless the first digit is a zero, in which case the last three digits are selected and the related XT parameter is set to 00010. See XT parameter for more information. Display will say (INPUT FORMAT 3 Digit (XX.X) or 4 Digit (XX.XX). Use key to toggle. 4 Software Configurations Press (*,0,4) to select from 4 standard software configurations. If you want your unit to look and act like it is running FOUR software, then this option will do this for you in one easy step. Use the "*" key to toggle through all selections: Select ( KEYPAD ) to exit without changing anything. Select ( R,N,C,A) for system to operate like FOUR software. Select ( N,N,C,A) to operate like FOUR software with the "TWO NATURALS" flag on. Select ( N,N,N,A) to operate with three Naturals and an additive. Select ( R,N,N,A) to operate with Regrind, two Naturals, and an additive. Component 2 is ALWAYS a NATURAL, and is never assigned a thumbwheel switch. Components 1, 3, and 4 are always assigned to thumbwheel switches. If ( R,N,C,A) is selected, component 2 is the ONLY natural and is set to 100. If ( N,N,C,A), ( N,N,N,A), or (R,N,N,A) is selected, the first, third, and forth components are assigned to switches 3, 1, and 2 respectively. Component 2 setting will be adjusted automatically at the start of each cycle to a number that will make all natural settings add up to 1000. In this way each NATURAL setting will represent a percent of the total natural blend. If the sum of natural settings exceeds 1000, component 2 will be set to 000, and the other naturals will be ratioed to each other. The TY and CS parameters are the ones that are altered. TY sets TYPE to Regrind, Natural or Additive. CS assigns the thumbwheel swatches. If CS = 40000 the software knows to calculate a setting based on the other naturals such that all settings total 1000. On 140, 240, 440 and 940 models: If (R,N,C,A) is selected, PARAMETERS are set: (1TY = REG) (2TY = NAT) (3TY = ADD) (4TY = ADD) (1CS 30000) (2CS 00100) (3CS 10000) (4CS 20000) Edition: March 24, 2008 43
Page 1 and 2: MAGUIRE PRODUCTS INC. Weigh Scale B
Page 3 and 4: WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 41: WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 51 and 52: CON TI NUE STOP END OF CYCL E CON T
Page 93 and 94:
WEIGH SCALE BLENDER® MAGUIRE PRODU
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
show all

WEIGH SCALE BLENDER® - Maguire Products

Create successful ePaper yourself

Delete template?

Save as template?