B-SX4T Series, B-SX5T Series External ... - Toshiba Tec Italia

More documents

Recommendations

Info

[C: Batch mode (Cut interval: 1, Issue count: 2)] • “Automatic forward feed standby” is set to ON in the system mode. • The rotary cutter is used. Cut position Head position (1) Idling (during the forward feed standby) (2) Feeds back to the home position. A (3) Completes printing the 1st label (A). A B (4) Starts printing the 2nd label (B). A B B (5) The 1st label (A) reaches the cut position and is cut. (6) Completes printing the 2nd label (B). B (7) Feeds the 2nd label (B) to the cut position. B (8) The 2nd label (B) reaches the cut position and is cut. (9) Since non-stop cutting is performed, paper is fed and stopped over the cut position. (10) Feeds back to the home position. (11) After 1 second, performs 13.7-mm automatic forward feed. - 170 -
[D: Strip mode (Issue count: 3)] Strip position Head position (1) Idling (2) Feeds back to the home position. A (3) Completes printing the 1st label (A). (4) Remove the 1st label (A). (5) Feeds back to the home position. B (6) Completes printing the 2nd label (B). (7) Remove the 2nd label (B). (8) Feeds back to the home position. C (9) Completes printing the 3rd label (C) * The next label is not printed until the printed label is removed. - 171 -
Page 1 and 2:
TOSHIBA Bar Code Printer B-SX4T Ser
Page 3 and 4:
Page 6.3.21 2-BYTE WRITABLE CHARACT
Page 5 and 6:
1. SCOPE This specification applies
Page 7 and 8:
Boot program Main program V1.0 V1.1
Page 9 and 10:
The model configuration and the dif
Page 11 and 12:
Available PCMCIA cards • LAN card
Page 13 and 14:
(13) Transmission Control: XON/XOFF
Page 15 and 16:
(14) Input/Output Signals Printer F
Page 17 and 18:
3.2 PARALLEL INTERFACE (1) Type: Ce
Page 19 and 20:
(9) Connector Pin Diagram (IEEE1284
Page 21 and 22:
nInit (Printer ← Host) • Reset
Page 23 and 24:
ECP mode Data 1 ~ 8 (Printer ←
Page 25 and 26:
Receiving data in the Compatibility
Page 27 and 28:
3.3 USB INTERFACE (1) Standard: Con
Page 29 and 30:
(3) Various parameters settings •
Page 31 and 32:
Parameter Initial Value Print densi
Page 33 and 34:
Parameter LAN enable/disable settin
Page 35 and 36:
(2) Storing PC interface commands P
Page 37 and 38:
(2) Where the Saved Data Call Comma
Page 39 and 40:
6.2 LIST OF COMMANDS (1) Commands r
Page 41 and 42:
6.3 COMMANDS FOR CREATING APPLICATI
Page 43 and 44:
[mm] Model B-SX4T B-SX5T Item Issue
Page 45 and 46:
Notes (1) Before changing the label
Page 47 and 48:
6.3.2 POSITION FINE ADJUST COMMAND
Page 49 and 50:
[Strip Position Fine Adjustment] 0.
Page 51 and 52:
NOTES: 1. If the head is being lift
Page 53 and 54:
(7) Procedure for label having less
Page 55 and 56:
6.3.3 PRINT DENSITY FINE ADJUST COM
Page 57 and 58:
6.3.5 IMAGE BUFFER CLEAR COMMAND [E
Page 59 and 60:
[Effective print area] [mm] Model B
Page 61 and 62:
[Line] (1) Horizontal line (In the
Page 63 and 64:
(4) Programming the radius of the r
Page 65 and 66:
N: Letter Gothic (Medium) 14.3 poin
Page 67 and 68:
noooooooooo: Increment and decremen
Page 69 and 70:
[Effective print area] [mm] Model B
Page 71 and 72:
q: Gothic725 Black : r: Chinese (24
Page 73 and 74:
(10) Increment/decrement Printing i
Page 75 and 76:
(14) Link field No. The link field
Page 77 and 78:
(3) The Bit Map Font Format Command
Page 79 and 80:
(2) Origin (0, 0) 30.0 mm Effective
Page 81 and 82:
6.3.9 OUTLINE FONT FORMAT COMMAND [
Page 83 and 84:
Po: Alignment (Omissible. If omitte
Page 85 and 86:
g: Drive Indicates where the TrueTy
Page 87 and 88:
[Effective print area] [mm] Item Mo
Page 89 and 90:
F: Price font 2 (POP font) G: Price
Page 91 and 92:
(6) Rotational angles of a characte
Page 93 and 94:
(13) Link field No. The link field
Page 95 and 96:
(4) When the drawing data is change
Page 97 and 98:
(2) Origin (0, 0) 30.0 mm Effective
Page 99 and 100:
e: Type of check digit 1: Without a
Page 101 and 102:
In the case of MSI, Interleaved 2 o
Page 103 and 104:
In the case of GS1 DataBar Format
Page 105 and 106:
In the case of Data Matrix (Two-dim
Page 107 and 108:
In the case of PDF417 (Two-dimensio
Page 109 and 110:
The maximum number of columns and r
Page 111 and 112:
In the case of MaxiCode Code (Two-d
Page 113 and 114:
In the case of RFID (Data write) Fu
Page 115 and 116:
can be designated by the parameters
Page 117 and 118:
This parameter is effective only fo
Page 119 and 120:
In the case of RFID (Data read) Fun
Page 121 and 122:
Explanation (1) The parameter, “N
Page 123 and 124: (3) Type of bar code 0: JAN8, EAN8
Page 125 and 126: : GS1 DataBar family GS1 DataBar Om
Page 127 and 128: In the case of QR code 1-cell width
Page 129 and 130: [GS1 DataBar Limited] Height [GS1 D
Page 131 and 132: (11) Increment/decrement Printing i
Page 133 and 134: [Data Command] [ESC] RB; A [LF] B [
Page 135 and 136: Cell size and the effective data ca
Page 137 and 138: (16) Explanation for the PDF417 and
Page 139 and 140: (19) Explanation for CP code ECC (
Page 141 and 142: Designation of access password regi
Page 143 and 144: (3) More than one Bar Code Format C
Page 145 and 146: (2) Origin (0, 0) 30.0 mm Effective
Page 147 and 148: 6.3.11 BIT MAP FONT DATA COMMAND [E
Page 149 and 150: Examples (1) Origin (0, 0) Effectiv
Page 151 and 152: (3) Origin (0, 0) 30.0 mm 12.5 mm E
Page 155 and 156: 6.3.13 BAR CODE DATA COMMAND [ESC]
Page 157 and 158: Symbol size Row Col ECC200 Numeric
Page 159 and 160: The maximum number of columns and r
Page 161 and 162: (4) CODE128 code selection check Ch
Page 163 and 164: (10) Transfer code for QR code 0 1
Page 167 and 168: (3) Origin (0, 0) 12.5 mm Effective
Page 169 and 170: Explanation (1) Number of labels to
Page 171 and 172: [C: Batch mode (Cut interval: 1, Is
Page 173: [C: Batch mode (Cut interval: 1, Is
Page 177 and 178: The expansion I/O is not installed:
Page 179 and 180: Correction for the ribbon saving ar
Page 181 and 182: Mirror printing bottom first Backin
Page 183 and 184: Notes Explanation of processes inv
Page 185 and 186: Transmissive sensor (when using pre
Page 187 and 188: [C: Batch (Cut)] • “Automatic f
Page 189 and 190: (4) Feed speed • A feed is perfor
Page 191 and 192: 6.3.16 EJECT COMMAND [ESC] IB Funct
Page 193 and 194: 6.3.17 FORWARD/REVERSE FEED COMMAND
Page 195 and 196: 6.3.18 STORAGE AREA ALLOCATE COMMAN
Page 197 and 198: • For the firmware V5.0 or greate
Page 199 and 200: 6.3.19 FLASH MEMORY FORMAT COMMAND
Page 201 and 202: 6.3.21 2-BYTE WRITABLE CHARACTER CO
Page 203 and 204: 6.3.23 BIT MAP WRITABLE CHARACTER C
Page 205 and 206: 1-byte writable character W/C = Wri
Page 207 and 208: [Nibble mode] (1) The writable char
Page 209 and 210: (9) Writable character set: 42 (24
Page 211 and 212: (11) Writable character set: 44 (48
Page 213 and 214: Examples Writable character set: 03
Page 215 and 216: ffff: Data count (Effective only fo
Page 217 and 218: [When TOPIX compression mode is sel
Page 219 and 220: Notes (1) The print origin of coord
Page 221 and 222: [TOPIX compression mode] 10.0 mm 24
Page 223 and 224: 6.3.26 SAVE START COMMAND (For ATA
Page 225 and 226:
6.3.28 SAVED DATA CALL COMMAND (For
Page 227 and 228:
6.3.30 HEAD BROKEN DOTS CHECK COMMA
Page 229 and 230:
Examples Load paper. Feed one lab
Page 231 and 232:
6.3.33 STATUS REQUEST COMMAND [ESC]
Page 233 and 234:
6.3.35 VERSION INFORMATION ACQUIRE
Page 235 and 236:
C: Stored PC command save file SOH
Page 237 and 238:
6.3.38 PRINTER OPTION STATUS ACQUIR
Page 239 and 240:
6.3.40 SOCKET COMMUNICATION PORT SE
Page 241 and 242:
6.3.42 PASS-THROUGH COMMAND [ESC] @
Page 243 and 244:
6.4 COMMANDS FOR SYSTEM ADMINISTRAT
Page 245 and 246:
oo: 1st byte code of the control co
Page 247 and 248:
6.4.2 FINE ADJUSTMENT VALUE SET COM
Page 249 and 250:
6.4.3 RFID PARAMETER SET COMMAND [E
Page 251 and 252:
6.4.4 BATCH RESET COMMAND [ESC] Z0
Page 253 and 254:
When print data for several labels
Page 255 and 256:
Xfgggggggg: User block access passw
Page 257 and 258:
Example Examples of the status to b
Page 259 and 260:
6.5.4 RFID DATA WRITE COMMAND [ESC]
Page 261 and 262:
20 Unlocked Unlocked Locked Unlocke
Page 263 and 264:
Qqrstuvw: Area lock designation (Ef
Page 265 and 266:
7. CONTROL CODE SELECTION (1) Autom
Page 267 and 268:
(2) Cutter Error • Rotary cutter
Page 269 and 270:
8.3 ERRORS IN WRITABLE CHARACTER AN
Page 271 and 272:
9. STATUS RESPONSE 9.1 FUNCTIONS Th
Page 273 and 274:
9.1.2 DETAIL STATUS LCD Message of
Page 275 and 276:
9.1.3 SUMMARY OF STATUS RESPONSE In
Page 277 and 278:
LCD Messages Printer Status Output
Page 279 and 280:
No. LCD Messages of Upper line (Eng
Page 281 and 282:
NOTE 3: ◦: ON : Blinking •: OFF
Page 283 and 284:
No. DUTCH No. SPANISH No. JAPANESE
Page 285 and 286:
12. CHARACTER CODE TABLE The follow
Page 287 and 288:
(5) PC-851 0 1 2 3 4 5 6 7 8 9 A B
Page 289 and 290:
(9) PC-1252 0 1 2 3 4 5 6 7 8 9 A B
Page 291 and 292:
(13) LATIN9 0 1 2 3 4 5 6 7 8 9 A B
Page 293 and 294:
(3) PC-852 0 1 2 3 4 5 6 7 8 9 A B
Page 295 and 296:
(7) LATIN9 0 1 2 3 4 5 6 7 8 9 A B
Page 297 and 298:
(2) PC-8 B-SX4T 0 1 2 3 4 5 6 7 8
Page 299 and 300:
(4) PC-851, PC-855, PC-1250, PC-125
Page 301 and 302:
(6) PC-1253 B-SX4T 0 1 2 3 4 5 6 7
Page 303 and 304:
12.4 OCR-B (Bit map font type: T) (
Page 305 and 306:
(3) PC-852 B-SX4T 0 1 2 3 4 5 6 7
Page 307 and 308:
(5) PC-1252, PC-1254, LATIN9 B-SX4
Page 309 and 310:
12.5 TEC OUTLINE FONT 1 (Outline fo
Page 311 and 312:
(5) PC-851 0 1 2 3 4 5 6 7 8 9 A B
Page 313 and 314:
(9) PC-1252 0 1 2 3 4 5 6 7 8 9 A B
Page 315 and 316:
(13) LATIN9 0 1 2 3 4 5 6 7 8 9 A B
Page 317 and 318:
12.7 TEC OUTLINE FONT 2, 3, GOTHIC7
Page 319 and 320:
(5) PC-851 0 1 2 3 4 5 6 7 8 9 A B
Page 321 and 322:
(9) PC-1252 0 1 2 3 4 5 6 7 8 9 A B
Page 323 and 324:
(13) LATIN9 0 1 2 3 4 5 6 7 8 9 A B
Page 325 and 326:
(2) GB18030 code tables TBD - 321 -
Page 327 and 328:
TBD - 323 -
Page 329 and 330:
12.9 TrueType FONT (1) PC-850 (2) P
Page 331 and 332:
(5) PC-851 (6) PC-855 - 327 -
Page 333 and 334:
(9) PC-1252 (10) PC-1253 - 329 -
Page 335 and 336:
(13) LATIN9 2 3 4 5 6 7 8 9 A B C D
Page 337 and 338:
- 333 -
Page 339 and 340:
- 335 -
Page 341 and 342:
- 337 -
Page 343 and 344:
- 339 -
Page 345 and 346:
- 341 -
Page 347 and 348:
- 343 -
Page 349 and 350:
- 345 -
Page 351 and 352:
- 347 -
Page 353 and 354:
- 349 -
Page 355 and 356:
- 351 -
Page 357 and 358:
- 353 -
Page 359 and 360:
- 355 -
Page 361 and 362:
(4) NW-7 2 3 4 5 6 7 0 SP 0 1 1 A a
Page 363 and 364:
Value Code Table VALUE CODE A CODE
Page 365 and 366:
(8) PDF417 The following modes are
Page 367 and 368:
(10) QR code When manual mode is se
Page 369 and 370:
(11) Postal code Customer bar code
Page 371 and 372:
How to send control code data: SOH
Page 373 and 374:
(14) GS1 DataBar Expanded/GS1 DataB
Page 375 and 376:
(15) RFID [Transfer Code] 0 1 2 3 4
Page 377 and 378:
Type of Bar Code: JAN13, EAN13 (1)
Page 379 and 380:
Type of Bar Code: UPC-E (1) No affi
Page 381 and 382:
Type of Bar Code: JAN8 + 5 digits,
Page 383 and 384:
Type of Bar Code: JAN13 + 5 digits,
Page 385 and 386:
Type of Bar Code: UPC-A + 5 digits
Page 387 and 388:
Type of Bar Code: UPC-E + 5 digits
Page 389 and 390:
Type of Bar Code: Interleaved 2 of
Page 391 and 392:
Type of Bar Code: CODE39 (Standard)
Page 393 and 394:
Type of Bar Code: No auto selection
Page 395 and 396:
Type of Bar Code: POSTNET (1) Auto
Page 397 and 398:
15. AUTOMATIC ADDING OF START/STOP
show all

B-SX4T Series, B-SX5T Series External ... - Toshiba Tec Italia

Create successful ePaper yourself

Delete template?

Save as template?