OVERHEAD LINE SPLICES

SECTION DFDISTRIBUTION CONNECTORSTINNED COPPER STACKING TERMINAL LUGS FOR USEWITH TYPE CHL LUGSTYPE CSLCOPPERCSL• For use with VERSA-CRIMP ® or conventional tooling• The offset heights and mounting pad dimensions allowstacking on top of CHL lugs so that two conductors canbe connected to each NEMA two hole position on a terminalspade or bus bar.• The same crimping dies install this series as used ontype CHL.• Recommended for copper conductor onlyMaterial:Copper Tin Plated.(1)CATALOGNUMBERCONDUCTOR RANGE& O.D.-INCHES-CRIMPINGDIE INDEXDIMENSIONSINCHES (MM)B C F H LAPPROX.WT. 100LBS. (KG)I.D.(INCHES)CSL10BN1/0 Str..360-.38312, 1/2 TQ, 421.37(35)0.84(21)0.93(24)1.46(37)5.00(127)19 (9) .383CSL20BN2/0 Str..405-.43013, 9/16, TS, 451.50(38)0.84(21)0.93(24)1.50(38)5.12(130)20 (9) .429CSL30BN3/0 Str..455-.48014, 9/16, TU, 501.50(38)0.90(23)1.00(25)1.62(42)5.37(136)21 (10) .480CSL40BN4/0 Str..505-.53515, 5/8-1, TWTY, 541.62(41)1.03(26)1.00(25)1.68(43)5.43(138)26 (12) .538DF26CSL250BNCSL300BNCSL350BN250 Str..550-.580300 Str..610-.640350 Str..660-.69016, 11/16, TR, 6017, 781, TV, 6618, 840, TX, 711.62(41)2.00(51)2.00(51)1.12(28)1.21(31)1.31(33)1.00(25)1.00(25)1.00(25)1.75(44)1.81(46)1.87(47)5.50(140)5.87(149)5.87(149)31 (14) .58540 (18) .64049 (22) .692CSL400BN400 Str..715-.74519, 15/16, TX, 762.12(54)1.40(36)1.00(25)1.93(49)6.12(155)62 (28) .745CSL500BN500 Str..795-.83020, 1, TH, 872.25(57)1.53(39)1.00(25)2.06(52)6.37(162)82 (37) .823CSL600BN600 Str..870-.90522, 1-1/8, 962.68(68)1.68(43)1.00(25)2.18(55)6.87(174)133 (51) .908CSL750BNCSL750BNTT (1)700-750 Str..964-1.01024, 1-5/16, 1062.87(73)1.90(48)1.06(27)2.31(59)7.25(184)133 (60) 1.014CSL800BN800 Str..988-1.04625, 1-5/16, 1062.93(74)1.96(50)1.12(28)2.50(64)7.68(195)154 (70) 1.036CSL1000BNCSL1000BNTT (1)1000 Str.1.124-1.15227, 1-1/2, 1253.00(76)2.18(55)1.12(28)2.62(67)7.87(200)186 (84) 1.162NOTE: Anderson’s VC63 Versa-Crimp tool will install sizes thru 500 MCM AHL-500-BN. The VC6-FT Versa-Crimp installs thru750 MCM AHL-750 BN (Aluminum). A VC8 Versa-Crimp tool will accommodate sizes from 3/0 stranded through 1000MCM AL / 1500 MCM CU.• VC7 / VC7FT series tools recommended for copper lugs.(1) “TT” suffix indicates pad is trimmed to 1-3/4” max. width to allow side-by-side NEMA mounting.DF-26April 2012HUBBELL ® Power Systems