User Manual - Terasic

More documents

Recommendations

Info

36. Compile the project, by selecting Processing > Start Compilation, as shown in Figure 7-47.Figure 7-48 shows the compilation process.Figure 7-47 Start CompilationFigure 7-48 Execute Compile114
37. A dialog box will appear upon successful completion of the compile, as shown in Figure 7-49.Figure 7-49 Compile project completely38. Now, we will assign the inputs and outputs of the circuit to specific pins. Select Assignments >Pin Planner from the menubar, as shown in Figure 7-50. The pin planner is shown in Figure 7-51.Figure 7-50 Pins menu115
Page 4 and 5:
Chapter 1IntroductionThe DE0-Nano b
Page 6:
1.2 About the KITThe kit comes with
Page 9 and 10:
2.3 Power-up the DE0-Nano BoardThe
Page 11:
Figure 3-1 Programming a serial con
Page 16 and 17:
Figure 3-7 Connections between FPGA
Page 18 and 19:
GPIO_03 PIN_A3 GPIO Connection DATA
Page 20 and 21:
Figure 3-10 Pin distribution of the
Page 22 and 23:
3.7 Digital AccelerometerThe ADXL34
Page 24 and 25:
• Power Distribution SystemFigure
Page 26 and 27:
8. The Control Panel is now ready f
Page 28 and 29:
4.3 Switches and PushbuttonsChoosin
Page 30 and 31:
The Sequential Read function is use
Page 32 and 33:
4.7 Overall Structure of the DE0-Na
Page 34 and 35:
The generated system is described u
Page 36 and 37:
Figure 5-3 The DE0-Nano Board Type
Page 38 and 39:
Figure 5-6 Project Settings• Proj
Page 40 and 41:
6.2 Before You BeginThis tutorial a
Page 42 and 43:
The driver is available within the
Page 44 and 45:
The driver will now be installed as
Page 46 and 47:
Figure 6-9 Project informationd. Cl
Page 48:
Figure 6-11 my_first_fpga project6.
Page 52 and 53:
always @ (posedge CLOCK_5)// on pos
Page 54 and 55:
14. Press the Esc key or click an e
Page 56 and 57:
d. Click Next.Figure 6-21 MegaWizar
Page 58 and 59:
Figure 6-23 MegaWizard Plug-In Mana
Page 60 and 61:
Figure 6-25 PLL Symbol11. Click OK
Page 62 and 63:
4. Place the new pin onto the BDF s
Page 64 and 65: Figure 6-31 Change the output BUS n
Page 66 and 67: Figure 6-34 lpm_mux settings9. Clic
Page 68 and 69: 15. Add input buses and output pins
Page 70 and 71: Figure 6-40 Adding the KEY [0] Inpu
Page 72 and 73: Figure 6-42 Completed Pin Planning
Page 74 and 75: Figure 6-44 Compilation Message for
Page 76 and 77: Figure 6-46 Programmer Window2. Cli
Page 78 and 79: Figure 6-48 Downloading CompleteCon
Page 80 and 81: Figure 6-50 Setting unused pinsClic
Page 82 and 83: Figure 7-1 Start to Create a New Pr
Page 84 and 85: Figure 7-5 New Project Wizard: Fami
Page 86 and 87: Figure 7-8 A New Complete Project5.
Page 88 and 89: Figure 7-12 Create New System[2]7.
Page 90 and 91: Figure 7-15 Nios II Processor9. Cli
Page 92 and 93: Figure 7-17 Rename the CPU (1)Figur
Page 94 and 95: Figure 7-20 JTAG UART’s add wizar
Page 96 and 97: Figure 7-22 Rename JTAG UART15. Add
Page 98 and 99: Figure 7-24 On-Chip Memory Box16. M
Page 100 and 101: Figure 7-26 Add On-Chip memory17. R
Page 102 and 103: Figure 7-29 Updated CPU settings19.
Page 104 and 105: Figure 7-31 Add PIO20. Click Finish
Page 106 and 107: 22. Select System > Auto-Assign Bas
Page 108 and 109: Figure 7-38 SOPC Builder generation
Page 110 and 111: 33. Figure 7-42 show a blank Verilo
Page 112 and 113: Figure 7-43 Input verilog TextFigur
Page 116 and 117: Figure 7-51 Blank Pins39. Input Loc
Page 118 and 119: Figure 7-54 Quartus II ProgrammerTh
Page 120 and 121: Figure 7-55 Nios II IDE New Project
Page 122 and 123: ● alt_sys_init.c: an initializati
Page 124 and 125: #include "system.h"#include "altera
Page 126 and 127: can write to the PIO data register,
Page 128 and 129: Figure 7-61 Configuring System Libr
Page 130 and 131: Figure 8-2 Pulse Width ModulationFi
Page 132 and 133: Table 8-1 DIP Switch SettingsDIP Sw
Page 134 and 135: Figure 8-5 ADC Reading hardware set
Page 136 and 137: • KEYThe KEY button is driven by
Page 138 and 139: Figure 8-11 4-wire SPI Timing Diagr
Page 140 and 141: • Input “1” to start Analog t
Page 142 and 143: In this demo, the accelerometer is
Page 144 and 145: Figure 9-1 Convert Programming File
Page 146 and 147: Figure 9-3 Select Devices Page146
Page 148 and 149: Figure 9-5 Compression the sof file
Page 150 and 151: Figure 9-7 Erasing setting in Quart
show all

User Manual - Terasic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?