User Manual - Terasic

More documents

Recommendations

Info

Figure 7-61 Configuring System Library Properties5. Click OK to close the Properties for hello_world_0_syslib dialog box and return to the IDEworkbench.Note: If you make changes to the system properties you must rebuild your project. To rebuild,right-click the hello_world_0 project in the Nios II C/C++ Projects tab and select Build Project.128
Chapter 8DE0-Nano Demonstrations8.1 System RequirementsMake sure Quartus II and NIOS II are installed on your PC.8.2 Breathing LEDsThis demonstration shows how to use the FPGA to control the luminance of the LEDs by means ofpulse-width modulation (PWM) scheme. The LEDs are divided into two groups, while one groupdims the other group brightens, vice versa. <strong>User</strong>s can change the PWM wave's duty ratio andfrequency to control the LED luminance and repetition rate.Figure 8-1 Shows a diagram of PWM signals to drive LED.129
Page 4 and 5:
Chapter 1IntroductionThe DE0-Nano b
Page 6:
1.2 About the KITThe kit comes with
Page 9 and 10:
2.3 Power-up the DE0-Nano BoardThe
Page 11:
Figure 3-1 Programming a serial con
Page 16 and 17:
Figure 3-7 Connections between FPGA
Page 18 and 19:
GPIO_03 PIN_A3 GPIO Connection DATA
Page 20 and 21:
Figure 3-10 Pin distribution of the
Page 22 and 23:
3.7 Digital AccelerometerThe ADXL34
Page 24 and 25:
• Power Distribution SystemFigure
Page 26 and 27:
8. The Control Panel is now ready f
Page 28 and 29:
4.3 Switches and PushbuttonsChoosin
Page 30 and 31:
The Sequential Read function is use
Page 32 and 33:
4.7 Overall Structure of the DE0-Na
Page 34 and 35:
The generated system is described u
Page 36 and 37:
Figure 5-3 The DE0-Nano Board Type
Page 38 and 39:
Figure 5-6 Project Settings• Proj
Page 40 and 41:
6.2 Before You BeginThis tutorial a
Page 42 and 43:
The driver is available within the
Page 44 and 45:
The driver will now be installed as
Page 46 and 47:
Figure 6-9 Project informationd. Cl
Page 48:
Figure 6-11 my_first_fpga project6.
Page 52 and 53:
always @ (posedge CLOCK_5)// on pos
Page 54 and 55:
14. Press the Esc key or click an e
Page 56 and 57:
d. Click Next.Figure 6-21 MegaWizar
Page 58 and 59:
Figure 6-23 MegaWizard Plug-In Mana
Page 60 and 61:
Figure 6-25 PLL Symbol11. Click OK
Page 62 and 63:
4. Place the new pin onto the BDF s
Page 64 and 65:
Figure 6-31 Change the output BUS n
Page 66 and 67:
Figure 6-34 lpm_mux settings9. Clic
Page 68 and 69:
15. Add input buses and output pins
Page 70 and 71:
Figure 6-40 Adding the KEY [0] Inpu
Page 72 and 73:
Figure 6-42 Completed Pin Planning
Page 74 and 75:
Figure 6-44 Compilation Message for
Page 76 and 77:
Figure 6-46 Programmer Window2. Cli
Page 78 and 79: Figure 6-48 Downloading CompleteCon
Page 80 and 81: Figure 6-50 Setting unused pinsClic
Page 82 and 83: Figure 7-1 Start to Create a New Pr
Page 84 and 85: Figure 7-5 New Project Wizard: Fami
Page 86 and 87: Figure 7-8 A New Complete Project5.
Page 88 and 89: Figure 7-12 Create New System[2]7.
Page 90 and 91: Figure 7-15 Nios II Processor9. Cli
Page 92 and 93: Figure 7-17 Rename the CPU (1)Figur
Page 94 and 95: Figure 7-20 JTAG UART’s add wizar
Page 96 and 97: Figure 7-22 Rename JTAG UART15. Add
Page 98 and 99: Figure 7-24 On-Chip Memory Box16. M
Page 100 and 101: Figure 7-26 Add On-Chip memory17. R
Page 102 and 103: Figure 7-29 Updated CPU settings19.
Page 104 and 105: Figure 7-31 Add PIO20. Click Finish
Page 106 and 107: 22. Select System > Auto-Assign Bas
Page 108 and 109: Figure 7-38 SOPC Builder generation
Page 110 and 111: 33. Figure 7-42 show a blank Verilo
Page 112 and 113: Figure 7-43 Input verilog TextFigur
Page 114 and 115: 36. Compile the project, by selecti
Page 116 and 117: Figure 7-51 Blank Pins39. Input Loc
Page 118 and 119: Figure 7-54 Quartus II ProgrammerTh
Page 120 and 121: Figure 7-55 Nios II IDE New Project
Page 122 and 123: ● alt_sys_init.c: an initializati
Page 124 and 125: #include "system.h"#include "altera
Page 126 and 127: can write to the PIO data register,
Page 130 and 131: Figure 8-2 Pulse Width ModulationFi
Page 132 and 133: Table 8-1 DIP Switch SettingsDIP Sw
Page 134 and 135: Figure 8-5 ADC Reading hardware set
Page 136 and 137: • KEYThe KEY button is driven by
Page 138 and 139: Figure 8-11 4-wire SPI Timing Diagr
Page 140 and 141: • Input “1” to start Analog t
Page 142 and 143: In this demo, the accelerometer is
Page 144 and 145: Figure 9-1 Convert Programming File
Page 146 and 147: Figure 9-3 Select Devices Page146
Page 148 and 149: Figure 9-5 Compression the sof file
Page 150 and 151: Figure 9-7 Erasing setting in Quart
show all

User Manual - Terasic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?