User Manual - Terasic

More documents

Recommendations

Info

Figure 6-34 lpm_mux settings9. Click Next.10. Click Next.11. Select the counter_bus_mux.bsf option.12. Click Finish. The Symbol window appears (see Figure 6-35 for an example).66
Figure 6-35 lpm_mux Symbol13. Click OK14. Place the counter_bus_mux symbol below the existing symbols on the BDF, as shown inFigure 6-36.Figure 6-36 Place the lpm_mux symbol67
Page 4 and 5:
Chapter 1IntroductionThe DE0-Nano b
Page 6:
1.2 About the KITThe kit comes with
Page 9 and 10:
2.3 Power-up the DE0-Nano BoardThe
Page 11:
Figure 3-1 Programming a serial con
Page 16 and 17: Figure 3-7 Connections between FPGA
Page 18 and 19: GPIO_03 PIN_A3 GPIO Connection DATA
Page 20 and 21: Figure 3-10 Pin distribution of the
Page 22 and 23: 3.7 Digital AccelerometerThe ADXL34
Page 24 and 25: • Power Distribution SystemFigure
Page 26 and 27: 8. The Control Panel is now ready f
Page 28 and 29: 4.3 Switches and PushbuttonsChoosin
Page 30 and 31: The Sequential Read function is use
Page 32 and 33: 4.7 Overall Structure of the DE0-Na
Page 34 and 35: The generated system is described u
Page 36 and 37: Figure 5-3 The DE0-Nano Board Type
Page 38 and 39: Figure 5-6 Project Settings• Proj
Page 40 and 41: 6.2 Before You BeginThis tutorial a
Page 42 and 43: The driver is available within the
Page 44 and 45: The driver will now be installed as
Page 46 and 47: Figure 6-9 Project informationd. Cl
Page 48: Figure 6-11 my_first_fpga project6.
Page 52 and 53: always @ (posedge CLOCK_5)// on pos
Page 54 and 55: 14. Press the Esc key or click an e
Page 56 and 57: d. Click Next.Figure 6-21 MegaWizar
Page 58 and 59: Figure 6-23 MegaWizard Plug-In Mana
Page 60 and 61: Figure 6-25 PLL Symbol11. Click OK
Page 62 and 63: 4. Place the new pin onto the BDF s
Page 64 and 65: Figure 6-31 Change the output BUS n
Page 68 and 69: 15. Add input buses and output pins
Page 70 and 71: Figure 6-40 Adding the KEY [0] Inpu
Page 72 and 73: Figure 6-42 Completed Pin Planning
Page 74 and 75: Figure 6-44 Compilation Message for
Page 76 and 77: Figure 6-46 Programmer Window2. Cli
Page 78 and 79: Figure 6-48 Downloading CompleteCon
Page 80 and 81: Figure 6-50 Setting unused pinsClic
Page 82 and 83: Figure 7-1 Start to Create a New Pr
Page 84 and 85: Figure 7-5 New Project Wizard: Fami
Page 86 and 87: Figure 7-8 A New Complete Project5.
Page 88 and 89: Figure 7-12 Create New System[2]7.
Page 90 and 91: Figure 7-15 Nios II Processor9. Cli
Page 92 and 93: Figure 7-17 Rename the CPU (1)Figur
Page 94 and 95: Figure 7-20 JTAG UART’s add wizar
Page 96 and 97: Figure 7-22 Rename JTAG UART15. Add
Page 98 and 99: Figure 7-24 On-Chip Memory Box16. M
Page 100 and 101: Figure 7-26 Add On-Chip memory17. R
Page 102 and 103: Figure 7-29 Updated CPU settings19.
Page 104 and 105: Figure 7-31 Add PIO20. Click Finish
Page 106 and 107: 22. Select System > Auto-Assign Bas
Page 108 and 109: Figure 7-38 SOPC Builder generation
Page 110 and 111: 33. Figure 7-42 show a blank Verilo
Page 112 and 113: Figure 7-43 Input verilog TextFigur
Page 114 and 115: 36. Compile the project, by selecti
Page 116 and 117:
Figure 7-51 Blank Pins39. Input Loc
Page 118 and 119:
Figure 7-54 Quartus II ProgrammerTh
Page 120 and 121:
Figure 7-55 Nios II IDE New Project
Page 122 and 123:
● alt_sys_init.c: an initializati
Page 124 and 125:
#include "system.h"#include "altera
Page 126 and 127:
can write to the PIO data register,
Page 128 and 129:
Figure 7-61 Configuring System Libr
Page 130 and 131:
Figure 8-2 Pulse Width ModulationFi
Page 132 and 133:
Table 8-1 DIP Switch SettingsDIP Sw
Page 134 and 135:
Figure 8-5 ADC Reading hardware set
Page 136 and 137:
• KEYThe KEY button is driven by
Page 138 and 139:
Figure 8-11 4-wire SPI Timing Diagr
Page 140 and 141:
• Input “1” to start Analog t
Page 142 and 143:
In this demo, the accelerometer is
Page 144 and 145:
Figure 9-1 Convert Programming File
Page 146 and 147:
Figure 9-3 Select Devices Page146
Page 148 and 149:
Figure 9-5 Compression the sof file
Page 150 and 151:
Figure 9-7 Erasing setting in Quart
show all

User Manual - Terasic

Create successful ePaper yourself

Delete template?

Save as template?