Untitled - Franke
Untitled - Franke
Untitled - Franke
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Securityware Products - Combi Units, Water Closets & Urinals<br />
30 1/2"<br />
(78cm)<br />
36 1/2"<br />
(93cm)<br />
2<br />
1<br />
14" (36cm)<br />
18" (46cm)<br />
HDCU1318C-DV shown<br />
7<br />
12 3/4"<br />
(32cm)<br />
17 3/4"<br />
(45cm)<br />
8<br />
6<br />
32 1/2"<br />
(83cm)<br />
15"<br />
(38cm)<br />
3<br />
4<br />
5<br />
HDCU1318- - - -<br />
Heavy Duty Combi Unit<br />
Fixture Specification:<br />
This Heavy Duty Combination Toilet/Lavatory is designed for areas requiring<br />
the utmost in vandal resistance. The fixture is fabricated from heavy 14<br />
gauge type 304 18-10 stainless steel and is designed to withstand loads of<br />
5000lbs (2267kg) without permanent damage. The cabinet and drawn<br />
bowls are seamlessly welded and are polished to a satin finish. The toilet<br />
seat is polished to a sanitary mirror finish. Internal piping is also 14 gauge<br />
type 304 18-10 stainless steel.<br />
Lavatory Oval Bowl (FB x LR x D):<br />
9 1/2" (24cm) x 14 3/4" (38cm) x 5" (13cm)<br />
Toilet<br />
Elongated design blow out jet bowl. The toilet requires a minimum of 35 PSI<br />
flow pressure. The toilet was tested and certified as a low water consumption<br />
toilet using 1.6gpf (6 litres). The trap will pass a 2 1/8" ball and has a seal<br />
of 3.5" min. The waste outlet extends a minimum of 3" behind the fixture<br />
and has a plain end OD of 2 3/8".<br />
The entire fixture is tested and certified to:<br />
ASME A112.19.2-2008/CSA B45.1-08 standards.<br />
Installation:<br />
These fixtures are designed to be installed onto finished walls which<br />
are serviceable from a pipe chase. Installation is achieved by threading six 1/2"<br />
(13mm) diameter threaded anchor rods to the back of the fixture. The anchor<br />
rods are then secured on the chase side of the wall by means of the supplied nuts<br />
and washers. (Standard included hardware is for walls up to 8" (20cm) thick).<br />
For existing walls, an optional metal cutout template is available. For new<br />
block (CMU) or poured concrete walls, an optional wall sleeve is available.<br />
Available Controls:<br />
The basin is controlled with an air-operated self closing valve with a non-hold<br />
open feature. Flow time is adjustable from approximately 5 to 60 seconds and<br />
has a flow rate of 0.5gpm (1.9 lpm). The valve is operated by a vandal resistant<br />
push button which requires less than 5lbs to operate. The valve can be mounted<br />
up to 10 feet (3 meters) away from the push button. Valve conforms to the<br />
requirements of ASME A112.18.1-2005/CSA B125.1-05. See basin valve<br />
options for available configurations.<br />
FIXTURE OVERVIEW:<br />
1 Bubbler<br />
2 Integral Soap Dish<br />
3 Toilet Roll Holder<br />
4 Lav Waste Outlet<br />
5 Toilet Waste Outlet<br />
6 Threaded Mounting Locations (6)<br />
7 Lav Push Buttons<br />
8 Waste Air Vent<br />
142 0311