Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

44 en | System Operation Fire Alarm Control PanelsiNotice!This test is available only if your system sends alarms and system information to a monitoringservice, and was programmed by the security installing company to permit communicatortests.NOTICE!!Warning!Reset upon termination of testTerminating the communicator test function (with the [*/Back] key) resets the communicatorand discards all unsent reports. When an off-normal condition occurs during a Communicatortest, the test automatically resets, clearing all reports, so the off-normal conditions are sentnormally.6.4.36.4.46.4.56.4.6Battery/NAC circuits testIf a power failure occurs, your control panel has a built-in battery that continues to power thesystem for several hours. The control panel automatically recharges the battery when power isrestored. In this test mode, the system operates the local NAC circuits and tests the batteryfor two seconds. The test results are shown at the end of the test, and are not reported to thecentral station. Pressing the [*/Back] key or the [#/Enter] key returns the display to standbymode, or the unit times out after three minutes.Activate ouputs testThis test turns a selected output on and off manually.Zone input level testThis test shows the status of a selected on-board point. The loop existing through the point isshown. Normal loops show 11 mA to 15 mA. Loops in alarm show over 25 mA, and loops introuble show less than 6 mA.Addressable point test (MUX test)This test allows activation of the special test mode for addressable (multiplex) devices. Thisapplies only if the optional D7039 Addressable Point Bus Expander module is installed. Whenthis test mode is selected, the system asks which bus to test, 1 or 2. Select 1 to test points 9to 128 and select 2 to test points 129 to 255. The system presents 5 options:1. List Devices: Shows the point numbers of all devices on the selected bus. Some devices(such as a dual point module) can use two or more points2. Show Holes: Lists locations on the bus that have no assigned device. This can help to findprogramming errors or identify an available address for a new device.3. Show Extras: The system scans the bus to identify devices that are present on the bus,but are not programmed into the system. Scanning the bus takes about 60 sec. Restoringthe bus after scanning also takes about 60 sec. The system cannot identify devices aboveAddress 128 on Bus 1, or below Address 129 on Bus 2. If you know that a device isconnected to the system but cannot find it, ensure that it is connected to the correct bus:9 to 128 for Bus 1, 129 to 255 for Bus 2.4. Show Missing: Lists devices programmed into the system but not present on the bus arelisted. Unless a device was programmed into the system (such as using MUX EDIT), it isnot considered missing.2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels System Operation | en 455. Show Status: After you select a device and press [#/Enter], this test shows detailedstatus information for the selected device. Eight conditions (not all status conditionsapply to or are supported by all devices) are shown. See the display shown below (whichupdates automatically every five seconds). For this option, you can view the status of anyMUX device regardless of which bus you selected to test when test mode was entered.– XxLxRxDxMxTxFxAxx is either 0 or 1 depending on whether the condition is false or true (0=false and 1=true). Theletters indicate the condition:– X: Reserved for future use.– L: Commanded relay state - this is how the output relay should be set. R: Actual relaystate - this is how the output relay is actually set.– D: Detector dirty - the detector is excessively sensitive.– M: Missing device - the device cannot be found on the loop. Unless a device wasprogrammed into the system (such as using MUX EDIT), it is not considered missing.– T: Tamper – the detector’s case was opened.– F: Loop fault - the loop from a contact input device is open, or the device is faulted. A:Loop alarm - the point is in alarm.Pressing [*/Back] ends the display for any of these modes.Examples: X0L0R0D0M0T0F0A0 (relay off, not dirty, not missing, no tamper, no fault and noalarm).6.4.76.5Sensitivity testTests the MUX smoke detectors to determine if they are within their normal range ofsensitivity. Press [Test] then [9].Point/Zone MappingThe control panel supports a flexible system to map input points to output points. The systemdefaults so that all NAC outputs are activated by a fire alarm. By programming output zones,you can create almost any output activation scheme, such as “floor above and floor below”activation or conditional elevator recall.Input points: Smoke detectors, pull stations, and so on.Zone: A group of input points (Zones 1 to 50 are configurable, 52 to 63 are activatedautomatically).Output points: NACs (notification appliance circuits) such as bells, strobes, and relays. Inputsactivate zones, and zones activate outputs.Zones 1 to 50 are available for the installer to program. Each input can activate one zone;however, any number of inputs can be mapped to the same zone.Zones above 50 are automatically activated by inputs. For example, any input that isconfigured as a waterflow type activates Zone 61 when it is alarmed. Any output driven byZone 61 activates when any waterflow type point is alarmed.Up to 64 zones can be assigned. The installer can assign Zones 1 to 50. Zones 51 to 63 arehard-coded to pre-assigned conditions.For how inputs control zones and zones control outputs, see the following figure:Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6: MethodenberichtBerliner pairfam Stu
Page 14 and 15: 14 en | Overview Fire Alarm Control
Page 17 and 18: Fire Alarm Control Panels Overview
Page 19 and 20: Fire Alarm Control Panels Overview
Page 22 and 23: 22 en | Installation Fire Alarm Con
Page 30 and 31: 30 en | Connection Fire Alarm Contr
Page 36 and 37: 36 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 94 and 95:
94 en | Control Panel Programming F
Page 96 and 97:
96 en | Control Panel Programming F
Page 98 and 99:
98 en | Specifications Fire Alarm C
Page 101 and 102:
Fire Alarm Control Panels Appendice
Page 103 and 104:
Page 105 and 106:
Page 107:
Page 110 and 111:
110 en | Appendices Fire Alarm Cont
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 122:
Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

Create successful ePaper yourself

Delete template?

Save as template?