Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

68 en | Control Panel Programming Fire Alarm Control PanelsPressing [Drill] retrieves the next point. For instance, if you are programming Point 2 and youpress [Drill], you retrieve the setting for Point 3.Pressing [History] retrieves the previous point. For instance, if you are programming Point 2and you press [History], you return to the setting for Point 1.Assigning point functionsShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBERThis feature assigns each point to one point function. A point function is a set ofcharacteristics that you can assign to selected points. There are 16 point functions to choosefrom.For more information about point functions, see Point function, 70. For the limitations whenassigning points to point functions that were programmed with a response time other thanFast, see Loop response, 72.Enter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG INPUT options.Press [0/Prog] to select FUNCTION. The following window appears:POINT FUNC. (___)(01 - 16):_______Enter the function number you wish to assign to the point and press [#/Enter]. The existingsetting is shown in parentheses on the first line. After you assign a point function, the previouswindow appears.Alarm/Trouble statusShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBERThis feature allows you to program the system response to an open loop condition. A shortedloop always causes an alarm condition.For acceptable programming selections for UL864 9 th edition Listed applications, seeProgramming features for UL864, 49.ALARM: A point in an open circuit state causes an alarm.TROUBLE: If a point is in an open circuit state, the system responds with a trouble condition.Enter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG INPUT options.Press [1] to select ALARM/TROUBLE. The following window appears:OPEN STATUS (__)1- ALARM2- TROUBLEPress [1] to select ALARM on open loop and ALARM on shorted loop or [2] to select TROUBLEon open loop and ALARM on shorted loop. The previous window appears. The existing settingis shown in parentheses on the first line.Output zonesShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBEREnter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG INPUT options.Press [2] to select OUTPUT ZONE. The following window appears:2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 69OUTPUT ZONE ZZZ(01 - 50):_______Press the number key that corresponds to your selection. ZZZ indicates the point beingprogrammed. The existing setting is shown on the second line. After you set up the outputzone, the previous window appears.VerificationShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBERThis feature resets the detector once to determine if the alarm recurs before annunciating orsending a signal. The total delay introduced by this feature is equal to the smoke power resettime plus five seconds. Alarm verification cannot be selected for points that are configured asWATERFLOW or SUPERVISORY types.Enter the point number you wish to verify and press [#/Enter]. The display scrolls through thePROG INPUT options.Press [3] to select VERIFICATION. The following window appears:ALARM VERIF (ZZZ)_______: YES(1) NO(0)ZZZ indicates the point being programmed. The existing setting is shown on the second line.Press either [1] to verify or [0/Prog] to not verify. The previous window appears.LatchingShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBERIf a zone is non-latching, the system resets the alarm status automatically (but does not resetsmoke power) when the input restores to the standby condition. Otherwise, the system mustbe manually reset.For acceptable programming selections for UL864 9 th edition Listed applications, seeProgramming features for UL864, 49.Enter the point number you wish to program and press [#/Enter]. The display scrolls throughthe PROG INPUT options.Press [4/◄] to select LATCHING. The following window appears:LATCHING? ZZZ:YES(1)NO(0)ZZZ indicates the point being programmed. The existing setting is shown on the second line.Press the number key that corresponds to your selection. Select YES for alarm.The previous window appears.Point descriptionShortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBERFor this feature, use the numeric keys to enter alphanumeric information to identify each input(such as initiating circuit). The system allows one 16-character description per input. Enter thepoint number you wish to program and press [#/Enter]. The display scrolls through the PROGINPUT options.Press [5] to select DESCRIPTION. The following window appears:PNT DSCRPTN ZZZ:Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6:
MethodenberichtBerliner pairfam Stu
Page 14 and 15:
14 en | Overview Fire Alarm Control
Page 17 and 18: Fire Alarm Control Panels Overview
Page 19 and 20: Fire Alarm Control Panels Overview
Page 22 and 23: 22 en | Installation Fire Alarm Con
Page 30 and 31: 30 en | Connection Fire Alarm Contr
Page 36 and 37: 36 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 98 and 99: 98 en | Specifications Fire Alarm C
Page 101 and 102: Fire Alarm Control Panels Appendice
Page 107: Fire Alarm Control Panels Appendice
Page 110 and 111: 110 en | Appendices Fire Alarm Cont
Page 118 and 119:
118 en | Appendices Fire Alarm Cont
Page 122:
Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?