Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

92 en | Control Panel Programming Fire Alarm Control PanelsIf a device is defective or not connected properly, the control panel shows:ERROR -DEVICE FAILEDFast ProgrammingFast programming proceeds the same as normal programming, except that when the device isprogrammed you are asked to remove the device:POINT NUMBER 009REMOVE DEVICEThen, you are asked to attach the next device at the next address:POINT NUMBER 010ATTACH DEVICEThis process continues until you press [*/Back]. All devices to be programmed must be of thesame type.8.9.3MUX Bus TypeShortcut: 0-PROG, 9-PROGRAM MUX, 3- BUS TYPEThis option configures the system for two independent Class B, Style 4 buses allowingaddresses up to 255.iNotice!Class A operation is not supported by the D7042 Eight Input Module; do not select Class Aoperation.The following window appears:MUX BUS TYPE ( )1- CLASS A2- CLASS BPress [2] to select Class B operation if the setting was changed from the default setting.For wiring details for a Class B configuration, see also the D7042/D7042B Multiplex Eight InputRemote Modules Installation Instructions (P/N: 42638)For more information regarding Class A and Class B wiring instructions, see also the D7039Multiplex Expansion Module’s Installation Guide (P/N: 38685).For mounting locations inside the FPD‐7024’s enclosure and wiring possibilities for the D7039and its I/O module, see the following figure:2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 93Figure 8.1: D7039 Mounting Location1 D7039 MUX Expansion module 5 Addresses 9 to 1282 Enclosure 6 MUX Class A3 FPD‐7024 Control board 7 Addresses 129 - 2554 I/O module for the D7039 MUXExpansion module8 MUX Class B8.9.4AUTO PROGRAMShortcut: 0-PROG, 9-PROGRAM MUX, 4- AUTO PROGRAMThis option provides a convenient way for the installer to configure the FPD‐7024 to operatewith the existing devices on the multiplex buses by scanning the buses for missing or newmultiplex devices.The following display appears:AUTO PROGRAM?_______:YES(1) NO(0)Press [1] to continue with auto programming or [0/Prog] to cancel. When you press [1], theFPD‐7024 checks for existing programming errors in which devices are programmedincorrectly in the space required for a lower-addressed multi-point device (such as a dualpoint module). If a point is found to be programmed under another device, the following errormessage appears for five seconds, and the auto programming process aborts:ADDRESS ERROR 1AT ADDRESS xxxIf no errors are found, the FPD‐7024 starts a scanning process that takes approximately oneminute to complete, while showing the following display:AUTO PROGRAMSCANNINGPLEASE WAIT...Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6:
MethodenberichtBerliner pairfam Stu
Page 14 and 15:
14 en | Overview Fire Alarm Control
Page 17 and 18:
Fire Alarm Control Panels Overview
Page 19 and 20:
Fire Alarm Control Panels Overview
Page 22 and 23:
22 en | Installation Fire Alarm Con
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
30 en | Connection Fire Alarm Contr
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
36 en | System Operation Fire Alarm
Page 38 and 39:
Page 40 and 41:
Page 42 and 43: 42 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 98 and 99: 98 en | Specifications Fire Alarm C
Page 101 and 102: Fire Alarm Control Panels Appendice
Page 107: Fire Alarm Control Panels Appendice
Page 110 and 111: 110 en | Appendices Fire Alarm Cont
Page 122: Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

Create successful ePaper yourself

Delete template?

Save as template?