Fire Alarm Control Panels - Bosch Security Systems

More documents

Recommendations

Info

94 en | Control Panel Programming Fire Alarm Control PanelsWhen the scanning is completed, the FPD‐7024 checks for missing devices. Missing devicesare addresses with no devices on the multiplex buses, but are programmed into theFPD‐7024’s site-specific memory area. If missing devices are detected, the FPD‐7024 showsthe following menu (where xxx is the address of the first point of the missing device):MISSING PT @ xxx0- DELETE POINT1- KEEP POINT2- DEL REMAIN3- KEEP REMAINDELETE POINT: If selected, the missing point and any addresses it implemented (up to eightfor an octal input module) are permanently deleted from the site specific memory area. If thedeleted device is an I/O module, the output zones that were programmed for the relay arereset to 0. If additional devices are found to be missing, the above display is repeated for eachmissing device.KEEP POINT: If selected, the FPD‐7024 retains the programming for the existing point andcontinues scanning for additional missing points.DEL REMAIN: If selected, the following prompt # KEY TO CONFIRM appears at the FPD‐7024.If the [#/Enter] key is pressed, all the missing points are deleted from the site-specific memoryarea and the auto program process continues with the devices found menu. If any other key ispressed, the existing point is kept and the control panel continues scanning for additionalmissing devices.KEEP REMAIN: If selected, no additional points are deleted and the auto program processcontinues with the Devices Found menu. Points individually deleted with the Delete Pointcommand before selecting the Keep Remain command stay deleted when Keep Remain isselected.!Warning!Missing points!Use the DEL REMAINING feature with caution. Any devices missing from the multiplex busesduring the DEL REMAINING operation, even momentarily, are permanently deleted. Thesepoints do not operate, and do not generate trouble conditions even if they are returned to thebus.When the delete point operation is finished, the FPD‐7024 shows for five seconds the totalnumber of points that were deleted from the control panel (xxx indicates the number of pointsthat were removed from the control panel’s site specific configuration).AUTO PROGRAMxxx POINTS DELETEDConfirm that only the expected number of points was removed from the system. Points thatare removed from the control panel’s site-specific configuration do not operate and are notsupervised even if they are returned to the bus.When the point delete process completes, the auto programming process automaticallychecks for new devices on the buses. New devices are found when a device is present on oneof the multiplex buses, but its address is not programmed into the control panel’s site-specificmemory. If new devices are detected, the FPD‐7024 shows the following menu (where xxx isthe address of the first new device found):2012.08 | 04 | F01U008458 Installation and Operation Manual Bosch Security System, Inc.
Fire Alarm Control Panels Control Panel Programming | en 95NEW DEVICE @ xxx2 – SINGLE INPUT3 – I/O MODULE4 – MUX SMOKE5 – SMOKE W/FRZ6 - DUAL INPUT7 - OCTAL INPUT0 – NO DEVICEUse this menu to define the device type. Press the number key that corresponds with thedevice type installed at the address. If a detected device should not be installed and should beleft inactive, press [0/Prog] to bypass the new device.!Warning!Device malfunction!Ensure that the correct device type is selected for each point. Incorrectly specified devicetypes can cause multiplex devices to malfunction or fail to operate.All inputs are configured to use Point Function 10 as they are added. Points added during autoprogramming are configured for the following operation:– Point Function 10 (Fire Alarm, Fast Response, Non-silenceable, Not Local-only)– Open Status = Trouble– Output Zone 9– Alarm Verify = NO– Latching = YESThe programming of input points can be changed when auto programming completes usingthe input-programming menu.When I/O modules are added during auto programming, the relay (second point) is configuredto activate on any alarm, non-silenceable (Zone 63). This can be changed when autoprogramming completes by using the output-programming menu.The FPD‐7024 performs some basic error checks when new devices are added. The followingerrors can be shown during the process of adding a device:ADDRESS ERROR #AT ADDRESS xxxIn the previous message, # is replaced by a code number and xxx is replaced by the affectedaddress that indicates the type of error.For code numbers and corresponding error message descriptions, see the following table:Code Error Description1 New point is under an existingpointThe new point is in the space required for anexisting multi-address device. This is checkedwhen auto programming first starts.2 Point overlaps existing point There are already devices configured at one ofthe addresses required for the new multi-pointdevice.Bosch Security System, Inc. Installation and Operation Manual 2012.08 | 04 | F01U008458
Page 6:
MethodenberichtBerliner pairfam Stu
Page 14 and 15:
14 en | Overview Fire Alarm Control
Page 17 and 18:
Fire Alarm Control Panels Overview
Page 19 and 20:
Fire Alarm Control Panels Overview
Page 22 and 23:
22 en | Installation Fire Alarm Con
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
30 en | Connection Fire Alarm Contr
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
36 en | System Operation Fire Alarm
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45: 44 en | System Operation Fire Alarm
Page 50 and 51: 50 en | Programming Fire Alarm Cont
Page 60 and 61: 60 en | Control Panel Programming F
Page 98 and 99: 98 en | Specifications Fire Alarm C
Page 101 and 102: Fire Alarm Control Panels Appendice
Page 107: Fire Alarm Control Panels Appendice
Page 110 and 111: 110 en | Appendices Fire Alarm Cont
Page 122: Bosch Security Systems, Inc.130 Per
show all

Fire Alarm Control Panels - Bosch Security Systems

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?