Spare parts11.2 Spare parts lists135 Locking ring140 Bearing143 NILOS ring144 Supporting disk / shim146 Locking ring160 Shaft sealing ring201 Adapter plate205 Screw210 Screw211 Screw lock220 Seal225 Seal301 Plug-in pinion305 Helical gear wheel331 Parallel key335 Locking ring340 Worm shaft345 Worm wheel346 Parallel key401 Screw plug411 Screw412 Screw lock413 Disk415 Locking ring418 Plug / sealing cap420 Vent filter430 EyeboltFigure 11-7 Helical worm <strong>gearbox</strong> sizes 38 - 88BA 2010118 Operating Instructions, 05/2011
Declaration of Incorporation, Declaration of12Conformity12.1 Declaration of IncorporationDeclaration of Incorporation according to Directive 2006/42/EC Annex II 1 B.The manufacturer Siemens Geared Motors GmbH, 72072 Tübingen, Germany, declares forthe partly completed machine● Single-stage helical <strong>gearbox</strong>es of typesE.38, E.48, E.68, E.88, E.108, E.128, E.148● Two- and three-stage helical <strong>gearbox</strong>es of typesD./Z.18, D./Z.28, D./Z.38, D./Z.48, D./Z.68, D./Z.88, D./Z.108, D./Z.128, D./Z.148,D./Z.168, D./Z.188● Parallel shaft <strong>gearbox</strong>es of typesF.28, F.38B, F.48B, F.68B, F.88B, F.108B, F.128B, F.148B, F.168B, F.188B, F.208● Bevel helical <strong>gearbox</strong>es of typesB.28, B.38, K.38, K.48, K.68, K.88, K.108, K.128, K.148, K.168, K.188● Helical worm <strong>gearbox</strong>es of typesC.28, C.38, C.48, C.68, C.88:The special technical documentation was generated according to Annex VII B.The following essential health and safety requirements from Directive 2006/42/EC Annex Iapply and have been fulfilled:● 1.1, 1.1.2, 1.1.3, 1.1.5● 1.2.4.4, 1.2.6● 1.3.1, 1.3.2, 1.3.3, 1.3.4, 1.3.6, 1.3.8.1● 1.4.1, 1.4.2, 1.4.2.1● 1.5.1, 1.5.2, 1.5.4, 1.5.5, 1.5.6, 1.5.8, 1.5.9, 1.5.10, 1.5.11, 1.5.13, 1.5.15● 1.6.1, 1.6.2● 1.7.1, 1.7.1.1, 1.7.2, 1.7.3, 1.7.4, 1.7.4.1, 1.7.4.2, 1.7.4.3The partly completed machine may only be commissioned once it has been established, ifapplicable, that the machine in which the partly completed machine is to be incorporatedmeets the provisions of Directive 2006/42/EC.The manufacturer is obligated to transmit the special technical documentation for the partlycompleted machine in electronic form to national authorities upon legitimate request.Person authorized to compile the relevant technical documentation: Georg Böing, Head ofResearch and Development Gears.Tübingen, April 11, 2011Georg BöingHead of Research & Development GearsJürgen PflaumHead of Quality ManagementBA 2010Operating Instructions, 05/2011 119