MOTOX gearbox - DS TECH

More documents

Recommendations

Info

Installation4.10 Removing and installing the shaft-mounted <strong>gearbox</strong>NoteThe hollow shaft is axially secured on the machine shaft by means of a shrink diskconnection.NoteApply a thin layer of grease to the shrink disk seat on the hollow shaft.NoteCoat with a suitable lubricant to prevent frictional corrosion of the contact surface on thecustomer's machine shaft in the vicinity of the bronze bush.Size 28, 208 reinforced Sizes 38 - 208 a Greasedb12345Absolutely grease-freeOuter ringInner ringTightening boltHollow shaftMachine shaftFigure 4-10 Mounting the shrink diskBA 201044 Operating Instructions, 05/2011
Installation4.10 Removing and installing the shaft-mounted <strong>gearbox</strong>Procedure1. Tighten the tightening bolts 3 handtight initially.2. Working round several times, evenly tighten the tightening bolts 3 by a ¼ turn each time(not crosswise).3. Fit the rubber cover cap or protection cover included in the scope of delivery,see Removing and installing the protection cover (Page 36).You have now installed the shrink disk.Table 4- 3Tightening torque for tightening boltGearbox size Thread size Strength classTightening torque[Nm]28 M5 8.8 538, 48, 68 M8 12.9 3588, 108, 128 M10 12.9 70148 M12 12.9 121168, 188 M14 12.9 193208M16 12.9 295M20 12.9 5704.10.3.2 Pulling off the shrink disk1. Working round several times, loosen the tightening bolts 3 one after the other, by a¼ turn each time.2. Pull the shrink disk off the hollow shaft.Sizes 38 - 208:If the outer ring does not come away from the inner ring, remove some of the tightening boltsand insert them into neighboring forcing threads.You will then be able to release the rings without difficulty.4.10.3.3 Cleaning and lubricating shrink disksSoiled shrink disks must be cleaned and regreased prior to fitting.Loosened shrink disks need not be dismantled and regreased before being retensioned.BA 2010Operating Instructions, 05/2011 45
Page 1: MOTOX gearboxBA 2010Operating Instr
Page 4 and 5: Legal informationLegal informationW
Page 6 and 7: Table of contents4.3 Tightening tor
Page 8 and 9: Table of contents12 Declaration of
Page 10 and 11: General information and safety note
Page 16 and 17: Technical description2.6 Shaft seal
Page 18 and 19: Technical description2.9 Rating pla
Page 20 and 21: Technical description2.10 Surface t
Page 22 and 23: Technical description2.10 Surface t
Page 24 and 25: Incoming goods, transport, and stor
Page 30 and 31: Installation4.2 General information
Page 32 and 33: Installation4.5 Gearbox with foot m
Page 34 and 35: Installation4.7 Gearbox with C-type
Page 36 and 37: Installation4.8 Mounting the input
Page 38 and 39: Installation4.9 Removing and instal
Page 40 and 41: Installation4.10 Removing and insta
Page 52 and 53: Commissioning5.4 Gearbox with backs
Page 54 and 55: OperationBA 201052 Operating Instru
Page 56 and 57: Faults, causes and remediesFaults C
Page 58 and 59: Faults, causes and remediesFaults C
Page 60 and 61: Service and maintenance8.1 General
Page 62 and 63: Service and maintenance8.2 Checking
Page 76 and 77: Service and maintenance8.5 Cleaning
Page 78 and 79: Service and maintenance8.9 Inspecti
Page 80 and 81: DisposalBA 201078 Operating Instruc
Page 82 and 83: Technical data10.1 Type designation
Page 84 and 85: Technical data10.2 General technica
Page 86 and 87: Technical data10.4 Sound-pressure l
Page 88 and 89: Technical data10.5 Types of constru
Page 96 and 97:
Technical data10.6 Oil quantities10
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Technical data10.6 Oil quantitiesTa
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Spare parts11.2 Spare parts lists11
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Spare parts11.2 Spare parts listsTa
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122:
Declaration of Incorporation, Decla
show all

MOTOX gearbox - DS TECH

Create successful ePaper yourself

Delete template?

Save as template?