MOTOX gearbox - DS TECH

More documents

Recommendations

Info

Service and maintenance8.5 Cleaning the vent filter8.5 Cleaning the vent filterClean the vent filter at least every 6 months, or more regularly depending on the degree ofsoiling.Procedure1. Unscrew the vent filter.2. Flush out the vent filter with benzine or a similar cleaning agent.3. Blow the vent filter out with compressed air.4. Seal the gearbox with the vent filter.You have now cleaned the vent filter.8.6 Checking the oil level sensor (optional)ATEX version gearboxesThe oil level sensor indicates the oil level only when the gearbox is shut down.Lower the oil level and fill it up again until the oil level sensor gives a switchingsignal.Please refer to the separate operating instructions for the oil level sensor.8.7 Cleaning the gearboxCAUTIONDust deposits prevent heat radiation and cause high housing temperatures.Keep the gearbox free from dirt and dust.CAUTIONDo not use a high-pressure cleaning appliance to clean the gearbox.Do not use tools with sharp edges.Switch off the power supply to the drive unit before cleaning it.BA 201074 Operating Instructions, 05/2011
Service and maintenance8.8 Checking tightness of fastening bolts8.8 Checking tightness of fastening boltsATEX version gearboxesLoose parts can cause sparks through impact.Entry of foreign bodies can cause sparks.NoteReplace damaged headless screws with new screws of the same type and strength class.Switch off the power to the drive unit and use a torque wrench to check the seating of allfastening bolts.The general tolerance for the tightening torque in Nm is 10 %. The friction coefficient is0.14 μ.Table 8- 5Thread sizeTightening torques for fastening boltsTightening torque at strength class8.8 10.9 12.9[Nm] [Nm] [Nm]M4 3 4 5M5 6 9 10M6 10 15 18M8 25 35 41M10 50 70 85M12 90 120 145M16 210 295 355M20 450 580 690M24 750 1 000 1 200M30 1 500 2 000 2 400M36 2 500 3 600 4 200BA 2010Operating Instructions, 05/2011 75
Page 1:
MOTOX gearboxBA 2010Operating Instr
Page 4 and 5:
Legal informationLegal informationW
Page 6 and 7:
Table of contents4.3 Tightening tor
Page 8 and 9:
Table of contents12 Declaration of
Page 10 and 11:
General information and safety note
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Technical description2.6 Shaft seal
Page 18 and 19:
Technical description2.9 Rating pla
Page 20 and 21:
Technical description2.10 Surface t
Page 22 and 23:
Technical description2.10 Surface t
Page 24 and 25:
Incoming goods, transport, and stor
Page 26 and 27: Incoming goods, transport, and stor
Page 28 and 29: Incoming goods, transport, and stor
Page 30 and 31: Installation4.2 General information
Page 32 and 33: Installation4.5 Gearbox with foot m
Page 34 and 35: Installation4.7 Gearbox with C-type
Page 36 and 37: Installation4.8 Mounting the input
Page 38 and 39: Installation4.9 Removing and instal
Page 40 and 41: Installation4.10 Removing and insta
Page 52 and 53: Commissioning5.4 Gearbox with backs
Page 54 and 55: OperationBA 201052 Operating Instru
Page 56 and 57: Faults, causes and remediesFaults C
Page 58 and 59: Faults, causes and remediesFaults C
Page 60 and 61: Service and maintenance8.1 General
Page 62 and 63: Service and maintenance8.2 Checking
Page 78 and 79: Service and maintenance8.9 Inspecti
Page 80 and 81: DisposalBA 201078 Operating Instruc
Page 82 and 83: Technical data10.1 Type designation
Page 84 and 85: Technical data10.2 General technica
Page 86 and 87: Technical data10.4 Sound-pressure l
Page 88 and 89: Technical data10.5 Types of constru
Page 96 and 97: Technical data10.6 Oil quantities10
Page 102 and 103: Technical data10.6 Oil quantitiesTa
Page 108 and 109: Spare parts11.2 Spare parts lists11
Page 114 and 115: Spare parts11.2 Spare parts listsTa
Page 122: Declaration of Incorporation, Decla
show all

MOTOX gearbox - DS TECH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?