MOTOX gearbox - DS TECH

More documents

Recommendations

Info

Service and maintenance8.2 Checking and changing lubricants8.2.10 Service life of the lubricantsNoteIn case of ambient conditions deviating from normal conditions, e.g. high ambienttemperatures, high relative humidity, aggressive ambient media, the intervals betweenchanges should be shorter. In such cases please contact Technical Support for assistance indetermining the individual lubricant change intervals.NoteOil sump temperatures above +80 °C can reduce service life. In this context, the rule is thatincreasing the temperature by 10 K will approximately halve the service life, as illustrated inthe figure titled "Guide values for oil change intervals".At an oil sump temperature of +80 °C, the following service life can be expected subject tocompliance with the properties required by Siemens Geared Motors GmbH:Table 8- 4Service life of the oilsType of oilMineral oilBiodegradable oilPhysiologically safe oil according to USDA-H1/-H2Synthetic oilService life10,000 operating hours or 2 years20,000 operating hours or 4 yearsBA 201070 Operating Instructions, 05/2011
Service and maintenance8.2 Checking and changing lubricants 12TIMineral oilSynthetic oilOil-bath long-term temperature [°C]Oil change interval in operating hours [h]Figure 8-6Guide values for oil change intervalsGrease service life of roller bearing greasesRoller bearings and the clearance in front are filled with sufficient grease.Under approved operating conditions and ambient temperatures, no regreasing is required.We recommend that the grease filling of the bearings is also changed when the oil or shaftsealing rings are replaced.BA 2010Operating Instructions, 05/2011 71
Page 1:
MOTOX gearboxBA 2010Operating Instr
Page 4 and 5:
Legal informationLegal informationW
Page 6 and 7:
Table of contents4.3 Tightening tor
Page 8 and 9:
Table of contents12 Declaration of
Page 10 and 11:
General information and safety note
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Technical description2.6 Shaft seal
Page 18 and 19:
Technical description2.9 Rating pla
Page 20 and 21:
Technical description2.10 Surface t
Page 22 and 23: Technical description2.10 Surface t
Page 24 and 25: Incoming goods, transport, and stor
Page 30 and 31: Installation4.2 General information
Page 32 and 33: Installation4.5 Gearbox with foot m
Page 34 and 35: Installation4.7 Gearbox with C-type
Page 36 and 37: Installation4.8 Mounting the input
Page 38 and 39: Installation4.9 Removing and instal
Page 40 and 41: Installation4.10 Removing and insta
Page 52 and 53: Commissioning5.4 Gearbox with backs
Page 54 and 55: OperationBA 201052 Operating Instru
Page 56 and 57: Faults, causes and remediesFaults C
Page 58 and 59: Faults, causes and remediesFaults C
Page 60 and 61: Service and maintenance8.1 General
Page 62 and 63: Service and maintenance8.2 Checking
Page 76 and 77: Service and maintenance8.5 Cleaning
Page 78 and 79: Service and maintenance8.9 Inspecti
Page 80 and 81: DisposalBA 201078 Operating Instruc
Page 82 and 83: Technical data10.1 Type designation
Page 84 and 85: Technical data10.2 General technica
Page 86 and 87: Technical data10.4 Sound-pressure l
Page 88 and 89: Technical data10.5 Types of constru
Page 96 and 97: Technical data10.6 Oil quantities10
Page 102 and 103: Technical data10.6 Oil quantitiesTa
Page 108 and 109: Spare parts11.2 Spare parts lists11
Page 114 and 115: Spare parts11.2 Spare parts listsTa
Page 122:
Declaration of Incorporation, Decla
show all

MOTOX gearbox - DS TECH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?