MOTOX gearbox - DS TECH

More documents

Recommendations

Info

Service and maintenance8.2 Checking and changing lubricants8.2.11 Recommended lubricantsDANGERThe lubricants used have not been approved to USDA -H1/-H2 (United States Departmentof Agriculture). They are not or only conditionally approved for use in the foodstuffs orpharmaceutical industry. If lubricants with USDA -H1/-H2 approval are required, pleasecontact Technical Support.CAUTIONIf you are working outside the temperature range specified in the Flender OperatingInstructions BA 7300, please contact Technical Support for advice on which oil to use.If the housing temperature exceeds a value of +80 °C, please contact Technical Support.NoteThe lubricants used are not or are only conditionally biodegradable. If lubricants classified asbiodegradable are required, please contact Technical Support.NoteThese recommendations are not a guarantee of the quality of the lubricant provided by yoursupplier. All lubricant manufacturers are responsible for the quality of their own products.The oil selected for use in the gearbox must be of the viscosity stated on the rating plate(ISO VG class). The viscosity class indicated applies for the contractually agreed operatingconditions.In the case of different operating conditions, please contact Technical Support.BA 201072 Operating Instructions, 05/2011
Service and maintenance8.3 Replacing bearingsThe lubricants suitable for use in the gearbox are listed in the Operating InstructionsBA 7300 "Gearbox Lubrication". We are familiar with the composition of these lubricants and,as far as we are currently aware, they possess state-of-the-art properties with regard to loadbearingcapacity, corrosion resistance (FZG test DIN 51354 = force level > 12), resistance togray staining and compatibility with seals and interior paint finishes as necessary for the typeof gearbox concerned. Therefore, we advise our customers to select one of the lubricantslisted in this table, taking into account the VG class specified on the rating plate.If, following agreement, gearboxes are filled at the factory with special lubricants for thespecial applications referred to above, this is shown on the rating plate.The warranty conditions are valid only for the lubricants listed in the Flender OperatingInstructions BA 7300. If you decide to use a different oil, you are responsible for the technicalsuitability of the lubricant.8.3 Replacing bearingsATEX version gearboxesBearing life depends very much on operating conditions. It is, therefore, verydifficult to calculate it reliably. In the operating conditions specified by the operator,bearing life can be calculated and indicated on the rating plate. If no information isgiven, changes in vibration and noise pattern can serve as an indicator that animmediate bearing replacement is necessary.8.4 Checking the gearbox for leaksOil or grease escaping in small quantities from the shaft sealing ring should be regarded asnormal during the running-in phase of 24 hours running time.If the quantities escaping are significant or leaking continues after the running-in phase, theshaft sealing ring must be replaced to prevent consequential damage.Shaft sealing rings are subject to natural wear. Service life depends on operating conditions.We recommend that shaft sealing rings are included in periodic maintenance and servicingwork on the system.BA 2010Operating Instructions, 05/2011 73
Page 1:
MOTOX gearboxBA 2010Operating Instr
Page 4 and 5:
Legal informationLegal informationW
Page 6 and 7:
Table of contents4.3 Tightening tor
Page 8 and 9:
Table of contents12 Declaration of
Page 10 and 11:
General information and safety note
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Technical description2.6 Shaft seal
Page 18 and 19:
Technical description2.9 Rating pla
Page 20 and 21:
Technical description2.10 Surface t
Page 22 and 23:
Technical description2.10 Surface t
Page 24 and 25: Incoming goods, transport, and stor
Page 30 and 31: Installation4.2 General information
Page 32 and 33: Installation4.5 Gearbox with foot m
Page 34 and 35: Installation4.7 Gearbox with C-type
Page 36 and 37: Installation4.8 Mounting the input
Page 38 and 39: Installation4.9 Removing and instal
Page 40 and 41: Installation4.10 Removing and insta
Page 52 and 53: Commissioning5.4 Gearbox with backs
Page 54 and 55: OperationBA 201052 Operating Instru
Page 56 and 57: Faults, causes and remediesFaults C
Page 58 and 59: Faults, causes and remediesFaults C
Page 60 and 61: Service and maintenance8.1 General
Page 62 and 63: Service and maintenance8.2 Checking
Page 76 and 77: Service and maintenance8.5 Cleaning
Page 78 and 79: Service and maintenance8.9 Inspecti
Page 80 and 81: DisposalBA 201078 Operating Instruc
Page 82 and 83: Technical data10.1 Type designation
Page 84 and 85: Technical data10.2 General technica
Page 86 and 87: Technical data10.4 Sound-pressure l
Page 88 and 89: Technical data10.5 Types of constru
Page 96 and 97: Technical data10.6 Oil quantities10
Page 102 and 103: Technical data10.6 Oil quantitiesTa
Page 108 and 109: Spare parts11.2 Spare parts lists11
Page 114 and 115: Spare parts11.2 Spare parts listsTa
Page 122: Declaration of Incorporation, Decla
show all

MOTOX gearbox - DS TECH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?